Bedienungsanleitung Gys STARTIUM 680E (Seite 9 von 28) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

625755

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

STARTIUM 330E / 480E / 680E / 980E

Charging multiple batteries simultaneously

You can charge multiple batteries simultaneously by connecting them in parallel. Connect the positive terminals to the

red clamp and the negative terminals to the black clamp. These batteries or group of batteries must all be the same

voltage, either 12 or 24V.

Charging in series is not recommended.

USE IN START MODE

Precautions before use

• Do not disconnect the battery from the vehicle. Disconnecting the battery may result in loss of information and a

possible inability to restart.

• The "START ENGINE" mode can detect sulphated batteries and in this event it will not start. The device will start an

automatic desulphation process prior to starting the battery to protect the vehicle electronics.

• If the battery is damaged, sulphated or too deeply discharged, starting is prevented in order to protect sensitive

vehicle electronic systems. In this event, the Startium shows intermittently “CIP” (Charge in Progress) and 0%. Battery’s

recovery is in progress.

Starting

Once the starter connected to the battery (see connection and disconnection) press key 13 to select the "START

ENGINE" mode. When this function is activated by pressing key 9, it will begin with a precharge.

STARTIUM 330E 50 - 80 Ah / 60Ah Instantaneous 5 min precharge

STARTIUM 480E 50 - 160 Ah / 100Ah Instantaneous 5 min precharge

STARTIUM 680E 50 - 220 Ah / 160Ah Instantaneous 5 min precharge

STARTIUM 980E 50 - 250 Ah / 220Ah Instantaneous 5 min precharge

By turning the key you activate the starter function.

If your engine does not start, wait 2 minutes between two start attempts. The attempt must last a maximum of 5

seconds.

Nb: A vehicle that will not start can be a problem other than a battery in poor condition. It could come from many other

causes.

After use follow the recommended instructions for disconnection.

TESTING THE ALTERNATOR

A test function of the alternator is available using key 12. It will indicate the charge capacity of the alternator by

displaying the voltage and the percentage.

Between 0 and 100% = The battery is not charged enough.

At 100% = Alternator ok.

Between 100% and 200% = Overcharge.

PROTECTION

This device has been designed with comprehensive protection functions:

• The charging clamps are fully insulated.

• A fuse provides proctection against reverse polarity and short circuits. The replacement request manual intervention.

STARTIUM 330E STARTIUM 480E / 680E STARTIUM 980E

FUSE

100A

FUSE

200A

FUSE

250A

• Thermal protection is provided by a thermostat (cooling time around 1/4h). The fault LED lights up in case of

overheating, the screen displays "TH".

• This device is equipped with a thermal proctection which will stop the power supply in case of over-heating. Allow 15

minutes for the unit to cool-down and place it in a well ventilated room.

• In case of a power supply problem, the device will stop, the fault LED only will ash and the screen will display "DEF".

If the problem is excessive an internal fuse protects the device. This fuse must be replaced by a qualied technician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys STARTIUM 680E Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info