Bedienungsanleitung Gys EASYMIG 140 (Seite 14 von 86) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665741

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

EASYMIG 130 / 140 / 150

ELECTRIC SAFETY

The machine must be connected to an earthed electrical supply. Use the recommended fuse

size.

An electrical discharge can directly or indirectly cause serious or deadly accidents.

Do not touch any live part of the machine (inside or outside) when it is plugged in (Torches, earth cable, cables,

electrodes) because they are connected to the welding circuit.

Before opening the device, it is imperative to disconnect it from the mains and wait 2 minutes, so that all the

capacitors are discharged.

Do not touch the torch or electrode holder and earth clamp at the same time.

Damaged cables and torches must be changed by a qualied and skilled professional. Make sure that the

cable cross section is adequate with the usage (extensions and welding cables). Always wear dry clothes in

good condition, in order to be insulated from the electrical circuit. Wear insulating shoes, regardless of the

environment in which you work in.

CEM CLASSIFIED MATERIAL

These Class A devices are not intended to be used on a residential site where the electric

current is supplied by the public network, with a low voltage power supply. There may be

potential difculties in ensuring electromagnetic compatibility on these sites, because of the

interferences, as well as radio frequencies.

This equipment does not comply with IEC 61000-3-12 and is intended to be connected to

private low-voltage systems interfacing with the public supply only at the medium- or high-

voltage level. On a public low-voltage power grid, it is the responsibility of the installer or

user of the device to ensure, by checking with the operator of the distribution network, which

device can be connected.

ELECTROMAGNETIC INTERFERENCES

The electric currents owing through a conductor cause electrical and magnetic elds

(EMF). The welding current generates an EMF eld around the welding circuit and the

welding equipment.

The EMF elds may disrupt some medical implants, such as pacemakers. Protection measures should be taken for

people wearing medical implants. For example, access restrictions for passers-by or an individual risk evaluation

for the welders.

All welders should take the following precautions in order to minimise exposure to the electromagnetic elds

(EMF) generated by the welding circuit::

• position the welding cables together – if possible, attach them;

• keep your head and torso as far as possible from the welding circuit;

• never enroll the cables around your body;

• never position your body between the welding cables. Hold both welding cables on the same side of your body;

• connect the earth clamp as close as possible to the area being welded;

• do not work too close to, do not lean and do not sit on the welding machine

• do not weld when you’re carrying the welding machine or its wire feeder.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys EASYMIG 140 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info