Bedienungsanleitung Gys EASYMIG 140 (Seite 18 von 86) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665741

Zoom out

Zoom in

Vorherige Seite

1/86

Nächste Seite

EASYMIG 130 / 140 / 150

SEMI-AUTOMATIC WELDING FOR ALUMINIUM (MIG MODE)

Set the voltage output and the wire speed according to the thickness of the weld piece, following the instructions/

recommendations printed on the side of the machine.

The Easymig 140 and 150 can be equipped to weld with aluminium wire Ø 0,8 or 1,0 (g II-B / p.74).

The Easy Mig 130 is delivered equipped for welding Aluminium of Ø 0.8mm (Occasional and non-intensive).

In this case the wire used should be stiff to facilitate wire feeding.

For use with aluminium, the gas requirement is pure argon (Ar). For the specic gas requirements please contact

your distributor. The gas ow in Aluminium is between 20 and 30 Litres/minute depending on the environment,

and the experience of the welder.

Below are the differences between welding with Steel and Aluminium :

- Specic rollers are needed for welding with Aluminium.

- Adjust the pressure of the drive rolls to prevent the wire being crushed.

- Only use a capilliary tube for welding with Steel or Stainless Steel.

- Use a special Aluminium Torch with a teon sheath to reduce friction.

DO NOT cut the sheath close to the joint, it is used to guide the wire from the the rollers.

- Contact Tube : Use a special aluminium contact tube specic to the diameter of wire being used.

GASLESS WIRE WELDING

Set the voltage output and the wire speed according to the thickness of the weld piece, following the instructions/

recommendations printed on the side of the machine.

The Easymig can weld gasless wire up to 0.9mm, if the polarity is reversed (g III / p.75) respecting a maximum

pressure of 5Nm. For parameters of use, please refer to the instructions indicated on page 74. Welding gasless

wire with a standard nozzle can lead to overheating and deterioration of the torch. It is recommended to use a

“No Gas” nozzle (ref. 041868), or remove the genuine nozzle (Fig. III / p.75).

ELECTRODE WELDING

• The reverse polarity cable must be disconnected in MMA (stick welding) mode in order to connect the electrode

holder and earth clamp. Connect the electrode holder and earth clamp as indicated on the electrode packaging.

• Respect the basic rules of welding.

• This device has 1 feature specic to Inverter machines :

- Anti-Sticking: Enables easy removal of the electrode from the metal. The anti-sticking feature, after its start,

requires approximately a 3 seconds delay before resuming normal welding operations.

SETTINGS PANEL (FIG V / P.75)

• Green light «ON»: when the machine is switched on the light

turns on.

• In case of power failure, the green light goes off but the device

remains powered while the power cable is unplugged.

• Orange light :

• Over-temperature: in such a case you shall wait a few minutes,

the light will turn off and the machine will start again.

• Over-current on primary circuit: in such a case you shall switch

off the machine (with the main switch) and switch on.

• Left button:

- MIG / MAG Welding : Adjust the wire feeder speed up to

maximum speed.

- MMA welding : Adjust the welding current.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys EASYMIG 140 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info