Bedienungsanleitung Gys GYSMI E160 (Seite 13 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665724

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

GYSMI E160

MADE IN FRANCE

INSTALLATION – PRODUCT OPERATION

Only qualied personnel authorized by the manufacturer should perform the installation of the welding equipment.

During set up, the operator must ensure that the machine is unplugged. Connecting generators in a series or a parallel

circuit is forbidden .

HARDWARE DESCRIPTION

These welding machines are Inverter technology based welding machines, portable, single phase, fan cooled, designed

for electrode welding (MMA) in direct current (DC). In MMA mode, these machines can weld all types of electrodes :

rutile, basic/low hydrogen, stainless and cast iron. In TIG mode, these machines can weld most metals except alumi-

nium and its alloys. They’re protected to work with generators (Alim 230 V +- 15% ou 400V +- 15% depending on the

reference).

POWER SUPPLY – STARTING UP

• The welders are tted with a 230V 16A socket type CEE7/7 which must be connected to a 230 V (50 - 60 Hz) power

supply WITH earth. Check that the power supply and its protection (fuse and/or circuit breaker) are compatible with

the current required by the machine. In some countries, it may be necessary to change the plug to allow the use at

maximum settings. Under intensive use, we recommend a 20A power supply for single phase models from 160A onward.

The user has to make sure that the plug can be reached.

• The device is switched on by pressing the «

» button.

• The device turns into protection mode if the power supply tension is over 265V. To indicate this default, the screen

displays

)

Normal operations resume once the power supply is back to its nominal range.

CONNECTION TO A GENERATOR

The machine can work with generators as long as the auxiliary power matches these requirements :

- The voltage must be AC, always set as specied, and the peak voltage below 400V,

- The frequency must be between 50 and 60 Hz.

It is imperative to check these requirements as several generators generate high voltage peaks that can damage these

machines.

ELECTRODE WELDING (MMA)

CONNECTIONS AND RECOMMENDATIONS

• Connect the cables, electrode holder and earth clamp in the connectors,

• Respect the welding polarities and intensities indicated on the electrodes boxes,

• Remove the electrode from the electrode holder when the machine is not in use.

• Your machine has 3 features exclusive to Inverters :

- The Hot Start delivers overcurrent at the beginning of the welding.

- The Arc Force delivers overcurrent to prevent sticking when the electrode enters the welding pool.

- The Anti-Sticking technology allows you to easily unstick your electrode.

• These machines have a «dropping» current output specication.

• The duty cycle following the norm EN60974-1 is indicated in the table here below

X @ 40°C (T cycle = 10 min) MMA TIG

I max 19% @ 160 A 24% @ 160 A

60% 90 A 105 A

100% 75 A 95 A

While under intensive use (> to duty cycle) the thermal protection can activate, in that case, the arc swictes off and the

thermal protection indicator switches on. The tests have been performed according to the standard at a temperature

of 40 °C.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys GYSMI E160 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info