Bedienungsanleitung Gys PROGYS 180A (Seite 10 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665726

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

PROGYS 180A

MADE IN FRANCE

EMC CLASSIFICATION

These Class A devices are not intended to be used on a residential site where the electric current is

supplied by the public network, with a low voltage power supply. There may be potential difculties in

ensuring electromagnetic compatibility on these sites, because of the interferences, as well as radio

frequencies.

This equipment does not comply with IEC 61000-3-12 and is intended to be connected to private

low-voltage systems interfacing with the public supply only at the medium- or high-voltage level. On

a public low-voltage power grid, it is the responsibility of the installer or user of the device to ensure,

by checking with the operator of the distribution network, which device can be connected.

This equipment complies with IEC 61000-3-11 if the power supply network’s impedance at the

electircal installation’s connection point is inferior to the network’s maximum admissible impendance

Zmax = 0.25 Ohms.

ELECTROMAGNETIC INTERFERENCES

The electric currents owing through a conductor cause electrical and magnetic elds (EMF). The

welding current generates an EMF eld around the welding circuit and the welding equipment.

The EMF elds may disrupt some medical implants, such as pacemakers. Protection measures should be taken for

people wearing medical implants. For example, access restrictions for passers-by or an individual risk evaluation for the

welders.

All welders should take the following precautions in order to minimise exposure to the electromagnetic elds (EMF)

generated by the welding circuit::

• position the welding cables together – if possible, attach them;

• keep your head and torso as far as possible from the welding circuit;

• never enroll the cables around your body;

• never position your body between the welding cables. Hold both welding cables on the same side of your body;

• connect the earth clamp as close as possible to the area being welded;

• do not work too close to, do not lean and do not sit on the welding machine

• do not weld when you’re carrying the welding machine or its wire feeder.

People wearing pacemakers are advised to consult their doctor before using this device.

Exposure to electromagnetic elds while welding may have other health effects which are not yet

known.

RECOMMENDATIONS TO ASSESS THE WELDING AREA AND WELDING INSTALLATION

Overview

The user is responsible for installing and using the arc welding equipment in accordance with the manufacturer’s

instructions. If electromagnetic disturbances are detected, it is the responsibility of the user of the arc welding equipment

to resolve the situation with the manufacturer’s technical assistance. In some cases, this remedial action may be as

simple as earthing the welding circuit. In other cases, it may be necessary to construct an electromagnetic shield around

the welding power source and around the entire piece by tting input lters. In all cases, electromagnetic interferences

must be reduced until they are no longer bothersome.

Welding area assessment

Before installing the machine, the user must evaluate the possible electromagnetic problems that may arise in the area

where the installation is planned.

. In particular, it should consider the following:

a) the presence of other power cables (power supply cables, telephone cables, command cable, etc...)above, below and

on the sides of the arc welding machine.

b) television transmitters and receivers ;

c) computers and other hardware;

d) critical safety equipment such as industrial machine protections;

e) the health and safety of the people in the area such as people with pacemakers or hearing aids;

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys PROGYS 180A Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info