Bedienungsanleitung Gys SMARTMIG 110 (Seite 14 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665733

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

SMARTMIG 110

Examples :

To weld 1.0mm thick steel :

• Move button (2) to the « A » position

• Move the regulator (1) to the zone of lightest colour and adjust « by sound » if required

ADVICE AND THERMAL PROTECTION

• Respect the normal rules of welding

• Leave the machine plugged in after welding to allow it to cool

• Thermal Protection : The LED will illuminate. Cooling will take between 10 and 15 minutes depending on the

ambient temperature.

DUTY CYCLE & WELDING ENVIRONMENT DURING USE

• The welding unit describes an output characteristic of "constant current" type. The duty cycles following the stan-

dard EN60974-1 (at 40°C on a 10mn cycle) are indicated in the table below :

Smartmig 110

X%-max 6% - 85A

12% 65A

During intensive use (> duty cycle) the thermal protection can activate, if this event the arc switches off and the ther-

mal protection indicator switches on. The welding machine has a constant voltage output.

Note: The machines’ duty cycle has been tested at room temperature (40°C) and has been determined by

simulation;

RISK OF INJURY DUE TO MOVING PARTS

The wire feeders contain moving parts that may catch hand, hair, clothes or tools which can lead to

injuries! Take extra care.

• Do not lay a hand to swivel or moving components or parts to the drive!

• Ensure that the housing covers or protective covers remain closed during operation!

TROUBLESHOOTING

SYMPTOMS POSSIBLE CAUSES REMEDIES

The welding wire speed is not

constant.

Debris is blocking up the opening. Clean out the contact tip or change it

and replace the anti-adherence product.

Ref.041806

The wire skids in the rollers Check the roller pressure or replace it.

- Wire diameter incompatible with roller

- Covering Wire guide in the torch incompatible

The wire-feeder motor doesn’t operate. Reel or roller brake too tight Adjust the brake and rollers.

Electrical supply problem. Check the power switch is in the "On" position.

Bad wire feeding. Covering wire guide dirty or damaged Clean or replace

Reel brake too tight Release the brake

No welding current Bad connection to the main supply Check the mains connection and ensure the

supply is 230V (1PH) power socket.

Bad earth connection. Check the earth cable (connection and clamp

condition).

The wire jams (after the rollers). Guide wire sheath crushed. Check the sheath and torch body.

Wire jammed in the torch Clean or replace.

No capillary tube. Check the presence of capillary tube.

Wire speed too fast Reduce the wire speed.

The welding bead is porous. Nozzle dirty Clean or replace nozzle.

Poor quality wire. Use suitable wire for no gas welding.

Work piece in bad condition. (rust, etc…) Clean the metal before welding.

The arc produces a lot of sparks Arc voltage too low or too high. See welding settings.

Bad earth connection. Adjust the earth cable for a better connection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys SMARTMIG 110 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info