Bedienungsanleitung Gys SMARTMIG 142 (Seite 14 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665734

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

SMARTMIG

GAS COUPLING

- Connect a pressure regulator to the gas bottle. Connect the welding machine using the pipes supplied, and place the two clamps to avoid lea-

kages.

- Set the gas ow by adjusting the dial located on the pressure regulator.

NB : to help facilitate the adjustment of the gas ow, operate the drive rollers by pressing the trigger of the torch (ensure that the drive roller is

completely loose so the wire is not fed through).

This procedure does not apply to «Gasless» welding mode.

CONTROL PANEL (FIG. VI)

Smartmig 142/152/162/182/183 Smartmig 3P

1- Voltage selection button A / B 1- Mode select button MIG/MMA.

2- Voltage selection button min/max. 2- Power adjustment knob MMA or MIG.

3- Wire speed regulator. 3- Wire speed regulator.

4- « SMART » settings table MIG/MAG 4- Voltage selection button A / B

5- Thermal Protection light. 5- « SMART » settings table MIG/MAG & MMA.

6- positions switch 6- Thermal Protection light.

DIRECTIONS OF USE (FIG VI)

MIG/MAG MODE:

SMARTMIG feature allows you to adjust the voltage and the wire speed.

Use the SMART table to nd the correct settings based on the type of wire, and the thickness of the metal workpiece.

Then based on the recommendation indicated, simply select :

• The voltage (buttons A/ B & min/max for SMARTMIG 142, 152 & 162 ; button A/B for SMARTMIG 3P)

• Wire speed - adjust the regulator (3) to the colour zone indicated.

Examples :

To weld 0.8mm thick steel, use 0.6 mm diameter steel wire (SMARTMIG 142, 152 & 162) :

• Move button (1) to the « A » position

• Move button (2) to the « min » position

• Move the regulator (3) to the zone of lightest colour and adjust « by sound » if required

To perform the same operation with SMARTMIG 3P :

• Move button (4) to the « A » position

• Move the regulator (2) to « min » or « max »

• Move the regulator (3) to the zone of lightest colour, and adjust « by sound » if required.

MMA MODE (SMARTMIG 3P ONLY) :

Connect the electrode holder and earth clamp to the machine, respecting the polarity indicated on the electrode packaging. Then adjust the posi-

tion.

Example :

For welding metal 4mm thick :

• Move button (1) to the « MMA » position.

• Adjust the regulator (2) to the zone corresponding with electrode diameter 2.5mm.

ADVICE AND THERMAL PROTECTION

• Respect the normal rules of welding

• Leave the machine plugged in after welding to allow it to cool

• Thermal Protection : The LED will illuminate. Cooling will take between 10 and 15 minutes depending on the ambient temperature.

DUTY CYCLE & WELDING ENVIRONMENT IN USE

• The welding unit describes an output characteristic of «constant current» type. The duty cycles following the standard EN60974-1 (at 40°C on a

10mn cycle) are indicated in the table here below :

x @40°C (T

cycle=10min)

142 / 152 162

182 183

MIG/MAG MMA

X%-max 20%-90A 20%-115A 25%-110A 15%-115A 15%-140A 15%-140A

60% 60A 70A 70A 40A 80A 90A

During intensive use (> duty cycle) the thermal protection can activate, if this event the arc switches off and the thermal protection indicator swit-

ches on. The welding machine has a constant current output in MIG/MAG. The welding machine has a constant voltage output in MMA.

Note: the running hot tests have been carried out at atmosphere temperature and duty cycle has been determined at 40°C by simulation.

These are A-class devices. They are designed to be used in an industrial or professional environment. In a different environment, it can be difcult to

ensure electromagnetic compatibility, due to conducted disturbances as well as radiation. From 1st December 2010, the new standard EN 60974-10

will be applicable : Warning: these materials do not comply with IEC 61000-3-12. If they are to be connected to a low-voltage mains supply, it is the

responsibility of the user to ensure they can be connected. If necessary consult the operator of your electrical distribution system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys SMARTMIG 142 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info