Bedienungsanleitung Gys TIG 160 DC LIFT (Seite 12 von 56) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665707

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

TIG 160 DC LIFT

MADE IN FRANCE

RECOMMENDATION ON METHODS OF ELECTROMAGNETIC EMISSIONS REDUCTION

a. National power grid: The arc welding machine must be connected to the national power grid in accordance with

the manufacturer’s recommendation. If interferences occur, it may be necessary to take additional preventive measures

such as the ltering of the power suplly network. Consideration should be given to shielding the power supply cable in a

metal conduit. It is necessary to ensure the shielding’s electrical continuity along the cable’s entire length. The shielding

should be connected to the welding current’s source to ensure good electrical contact between the conduct and the

casing of the welding current source.

b. Maintenance of the arc welding equipment: The arc welding machine should be be submitted to a routine

maintenance check according to the manufacturer’s recommendations. All accesses, service doors and covers should be

closed and properly locked when the arc welding equipment is on.. The arc welding equipment must not be modied

in any way, except for the changes and settings outlined in the manufacturer’s instructions. The spark gap of the arc

start and arc stabilization devices must be adjusted and maintained according to the manufacturer’s recommendations.

c. Welding cables: Cables must be as short as possible, close to each other and close to the ground, if not on the

ground.

d. Electrical bonding : consideration shoud be given to bonding all metal objects in the surrounding area. However,

metal objects connected to the workpiece increase the riskof electric shock if the operator touches both these metal

elements and the electrode. It is necessary to insulate the operator from such metal objects.

e. Earthing of the welded part : When the part is not earthed - due to electrical safety reasons or because of its size

and its location (which is the case with ship hulls or metallic building structures), the earthing of the part can, in some

cases but not systematically, reduce emissions It is preferable to avoid the earthing of parts that could increase the risk

of injury to the users or damage other electrical equipment. If necessary, it is appropriate that the earthing of the part

is done directly, but in some countries that do not allow such a direct connection, it is appropriate that the connection

is made with a capacitor selected according to national regulations.

f. Protection and plating : The selective protection and plating of other cables and devices in the area can reduce

perturbation issues. The protection of the entire welding area can be considered for specic situations.

TRANSPORT AND TRANSIT OF THE WELDING MACHINE

The machine is tted with handle(s) to facilitate transportation. Be careful not to underestimate the

machine’s weight. The handle(s) cannot be used for slinging.

Do not use the cables or torch to move the machine. The welding equipment must be moved in an

upright position.

Do not place/carry the unit over people or objects.

Never lift the machine while there is a gas cylinder on the support shelf. A clear path is available when

moving the item.

EQUIPMENT INSTALLATION

• Put the machine on the oor (maximum incline of 10°.)

• Ensure the work area has sufcient ventillation for welding, and that there is easy access to the control panel.

• The machine must not be used in an area with conductive metal dusts.

• The machine must be placed in a sheltered area away from rain or direct sunlight.

• The machine protection level is IP21, which means :

- Protection against acess to dangerous parts from solid bodies of a ≥12.5mm diameter and,

- Protection against vertically falling drops.

The power cables, extensions and welding cables must be fully uncoiled to prevent overheating.

The manufacturer does not incur any responsability regarding damages to both objects and persons

that result from an incorrect and/or dangerous use of the machine.

MAINTENANCE / RECOMMENDATIONS

• Maintenance should only be carried out by a qualied person. Annual maintenance is recommended.

• Ensure the machine is unplugged from the mains, and wait for two minutes before carrying out main-

tenance work. DANGER High Voltage and Currents inside the machine.

• Remove the casing 2 or 3 times a year to remove any excess dust. Take this opportunity to have the

electrical connections checked by a qualied person, with an insulated tool.

• Regularly check the condition of the power supply cable. If the power cable is damaged, it must be

replaced by the manufacturer, its after sales service or an equally qualied person.

• Ensure the ventilation holes of the device are not blocked to allow adequate air circulation.

• Do not use this equipment to thaw pipes, to charge batteries, or to start any engine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys TIG 160 DC LIFT Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info