Bedienungsanleitung Gys TIG 250 AC-DC (Seite 6 von 24) (Englisch)

665714

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

DESCRIPTION

Thank you for choosing this machine! To get the best use from your machine please read the following carefully.

The TIG 250 AC/DC is a portable, single phase, ventilated Inverter welding unit to be used with non consumable

electrode (TIG) in direct (DC) or alternative (AC) current. TIG welding requires a gas shield protection of

pure(Argon). In MMA mode, it allows you to weld with any kind of electrodes: rutile, basic, stainless steel or cast

iron.

The TIG 250 AC/DC can be equipped with a remote control or foot pedal.

The TIG 250 AC/DC has an integrated liquid cooling system to connect liquid cooled torches.

POWER SUPPLY – STARTING UP

• This machine is delivered with a 5 pin three-phase plug (3P + N + PE) 400V 16A type CEE17. The TIG 250 AC/DC

must be connected to a 400 V socket (50 - 60 Hz) WITH earth protected by a 16A circuit breaker and a 30mA

overcurrent discontactor. The absorbed current (I1eff) is indicated on the device, for its maximum setting.

Check that the power supply and its protection (fuse and/or circuit breaker) are compatible with the

current needed by the machine. In some countries, it may be necessary to change the plug to allow the

use at maximum settings.

This unit has an internal cooling liquid system which has 2 main functions: the cooling of the water torch if

connected and the cooling of internal spare parts. So the tank of the unit needs to be filled to the maximum line

indicated at the back of the machine.

•

The starting up is made by pushing on the standby button.

•

The device turns into protection mode if the power supply tension is under 360V or over 440V or if a

phase is missing. To indicate this default, the screen displays. Once in protection mode, you have to

unplug the device and plug it back into a socket delivering the correct voltage (see the table of error

messages).

• Fan: in MMA mode, the fan works nonstop. In TIG mode, the fan works only when welding, then stops after

cooling.

•

These are Class A devices. They are designed to be used in an industrial or professional environment. In a

different environment, it can be difficult to ensure electromagnetic compatibility due to conducted

disturbances as well as radiation

. They comply with the norm CEI 61000-3-12.

DEVICE PRESENTATION (FIG-1)

① Screen + potentiometers

② + polarity plug

③ - polarity plug

④ Gas connection for torch

⑤ Trigger connection

⑥ Water input for water cooled torch

⑦ Water output for water cooled torch

⑧ Remote control connection

⑨ 5A fuse support

⑩ ON / OFF switch

⑪ Power cable

⑫ Tank

⑬ Gas inlet

CONTROL BOARD (IHM) (FIG-2)

The control board is made of a colour TFT screen and two potentiometers. How it works in 3 states:

State 1 or Standby mode: with the potentiometer 1 you will be able to set the welding current, and with the

potentiometer 2 the parameters related to the welding current.

State 2 or Welding mode: by pushing the potentiometer 1 you will have access to the top menu. Then by turning the

button you will select the welding mode. You will exit this menu by waiting 8s or by pushing the potentiometer 2 ->

back to State 1.

State 3 or Welding parameters mode: by pushing the potentiometer 2 you will have access to the welding

parameters and you will see the selection by turning the button. You will exit this menu by waiting 8s or by pushing

the potentiometer 2 -> back to State 1.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gys TIG 250 AC-DC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info