Bedienungsanleitung Haas-Sohn Bench modules (Seite 4 von 6) (Englisch)

811993

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

The minimum dimensions are (see drawing):

D 50 cm

E 30 cm (from inner edge firebox opening).

Rückwand: rear wall Seitenwand: side wall

Unterlagsplatte: floor protector

Strahlungsbereich: radiation area

Floor protection slabs (support slabs) are available from our

accessories program and can be ordered from your specialist

stove dealer if required.

5. wood stove operation

The wood stove must only be heated by adults. Ensure that

children never stay alone around the chimney stove. (Do not

leave the wood stove without supervision for any length of

time). The wood stove must only be used in accordance with

this Operating Manual.

Please observe the safety instructions shown in Chapter 2.

5.1. Suitable fuels

The stove is suitable for low-smoke fuels. The fuels

approved for combustion are listed on the Equipment Sheet.

Note! Wood is not a slow-combustion fuel so that

continuous heating of the fireplace with wood overnight is

not possible.

Note:

Never use waste such as wallpaper, chipboard offcuts,

plastic materials or impregnated wood for heating!

5.2. Adjusting the combustion air damper

The correct setting of the combustion air damper of your

wood stove can be found in the enclosed Equipment Sheet.

Please adhere to these recommended settings to optimally

utilise the heating energy of the fuel, to save fuel and to

protect the environment.

Combustion air

1 = primary air I through the grate

2 = primare air II flows onto the fuel in a horizontal dir.

3 = secondary air / air wash system

pre-heated air from above is the main combustion

air for wood

5.3. Initial start-up of your wood stove

Prior to initial start-up remove any adhesive labels and all

accessory components from the ash pan or the firebox, this

also applies to any transport locks that may have been used.

On models with draft baffle plates made of ceramic fibre or

vermiculite please check if these plates are located in their

anchorages (these could have slipped from their position as a

result of the transport or the installation of the chimney

stove). Otherwise these plates must be carefully hooked into

position (see Equipment Sheet).

In the case of chimney stoves with ceramic tiles the warming

compartment tiles must be placed in the warming

compartment. The ceramic tiles should be wiped clean with a

dry cloth.

For initial heating, carefully charge the wood stove with fuel

and “burn in” with a low flame. All materials must slowly

get accustomed to the heat development. By careful initial

heating you will avoid cracks in the insulating bricks, paint

damage and material distortion. Any smell developing

through re-drying of the protective varnish will disappear

after a short time.

5.4. Lighting and heating

Initially place 2 to 3 wood billets (approx. 1.5 to 2.0 kg) on

the firebox floor or grate, uncoated paper, cardboard or a

lighting cube on top, followed by brushwood, firewood or

pieces of briquettes. All existing air control dampers must be

fully opened. After lighting, close the firebox door. After

this, set the air control dampers as specified in the enclosed

Equipment Sheet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haas-Sohn Bench modules Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Haas-Sohn Bench modules

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info