Bedienungsanleitung Haas-Sohn COMPACT-PELLET 310 (Seite 7 von 40) (Englisch)

812036

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Picture 4: Windbreak of the air-intake line

The following table is applicable for the

dimensioning of the air intake:

Diameter

Intake tube* Maximum

length* Max. number

of 90° bends

50mm 0.5 m 1

70mm 1 m 1

100mm 3 m 3

*The respective specifications are independently applicable.

The cross-section is to be chosen accordingly when using a

flat duct or the like.

If the dimensions fall below, it can happen,

that the quantity of combustion air is

insufficient. As a result, an increased

formation of slag occurs in the burner tray

and consequently safety shutdowns.

Connection to the power supply:

Connect the stove to the power supply with

the supplied mains cable (see Picture 1).

4. The functional features of the pellet

stove

The functioning method of your pellet stove is

designed for the maintaining of a constant,

comfortable room temperature. The

generation of heat in the stove is therefore

governed automatically according to the

required room temperature set by the

operator (target temperature). Depending on

the difference in temperature between target-

and current room temperature (actual

temperature), in a modular fashion the

controller selects the output or the „Standby“-

operation. As a result, the pellet stove

ensures a greatest possible adaptation of the

burning behavior to the situation in the room

of installation, without constant manual

corrections.

5. Operating states of the pellet stove:

The function of the pellet stove is

characterized by eight operating states:

5.1. Measurement – degree of soiling of

burner tray before the start phase

The start phase begins when the current

room temperature falls below the set target

temperature by 1°C and the stove has cooled

to a temperature of less than 80 C°.

Before the beginning of the start phase, a

measurement of the degree of soiling of the

burner tray is performed.

During this measurement, the components

are switches as follows:

Induced draught blower – ON

Convection air blower – OFF

Screw conveyor – OFF

Ignition – OFF

If the „Burner test“ concludes successfully,

i.e. the burner tray is not or only slightly

soiled, then transition to the operating state

Start Phase takes place.

If the „Measurement – Burner tray soiling“ is

not concluded successfully, i.e. the burner

tray is more heavily soiled than is permitted,

then transition to the operating state Safety

Shutdown takes place and the following error

message appears on the display of the

control unit.

Quit

15:00 24.01.2004

Fault

Shutdown Air Volume

Check burner

Picture 5: Error message

5.2. Start phase

After successfully concluded „Measurement –

Burner tray soiling“, transition to the operating

state Start Phase takes place.

In the „Start phase“, the burner tray is filled

with a precisely defined quantity of fuel and

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haas-Sohn COMPACT-PELLET 310 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Haas-Sohn COMPACT-PELLET 310

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info