Bedienungsanleitung Haas-Sohn HSP1.17 (Seite 12 von 31) (Englisch)

812047

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

A simple quality test: Put a few wood pellets in a glass of

water:

Good quality: Pellets sink

Lower quality: Pellets float.

The use of lower-quality or unauthorised fuel adversely

affects the operation of your pellet stove and may in

addition lead to the lapse of the guarantee and the

associated product liability. Unauthorised fuels include

woodchips, straw and maize. Burning wood pellets of

poor quality leads to shortening of the cleaning intervals

and to increased fuel consumption, so the pellet tank

has to be filled more frequently.

Wood pellets are packed in plastic or paper sacks. To

ensure problem-free combustion of the wood pellets it is

necessary to dry the fuel as much as possible and to

transport and store it free from dirt. On contact with

moisture, pellets swell considerably.

When filling the storage container with wood pellets,

make sure that the pellet sacks do not come into contact

with the hot surfaces of the stove.

Two kilograms of wood pellets have about the same

energy content as a litre of “extra light heating oil.” In

terms of volume, 3 m3 of wood pellets are equivalent to

about 1,000 litres of heating oil. Variations in heat output

by the pellet stove are caused not only by the quality of

the pellets but also by the raw material of the wood (type

of wood).

7.2. Commissioning your pellet stove

The materials making up your pellet stove must

gradually get used to the heat generation. By careful

warming up you avoid cracks in the combustion

chamber plates, damage to the paintwork and warping

of materials. So do not set the target temperature too

high on the control unit (about 1.5°C to 2°C higher than

the current room temperature).

 Before commissioning, remove any stickers and

any accessories from the pellet tank and the

combustion chamber.

 Check that the combustion chamber cladding is

attached to its fastenings. (This might have

slipped out of its position as a result of the

transportation or installation of the stove).

 Check that the combustion pot fits perfectly in its

frame.

 Close the combustion chamber door.

 Fill the storage container with standard wood

pellets (Ø 6 mm).

 Insert the mains cable.

 Once the toggle switch has been set to ON, the

control unit commences initialisation. This

process takes a few seconds.

 After initialisation, the Information screen

appears – press the right key (Menu) – move

cursor to Operating mode – press the right key

(Select) – select the desired operating mode

with the cursor – press the right key (Save).

Tip!!

Only when commissioning, place about 30

pellets in the burner. This will speed up the

ignition process.

General:

If the ignition phase could not be successfully

run i.e. no flame generation or the required

temperature could not be reached at the flue

gas thermosensor, then a safety shutdown is

initiated and an error message generated (“Ignition

phase target temp. flue gas not reached – check burner

– date and time”).

Note: Any smoke generation caused by further

drying of the paint stops after a short while. Please

properly ventilate the room where the stove is

installed. However, the paint does not contain any

toxic vapours.

8. Cleaning and maintenance work

The functioning of your device depends to a large extent

on regular expert maintenance. Because of the ash

accumulation resulting from the combustion of wood

pellets, constantly recurring cleaning and maintenance

work needs to be carried out. This will permit operation

to be as trouble-free as possible.

The frequency of maintenance in turn depends to a large

extent on the pellet quality (ash content). Quality pellets

have a low ash content of about 0.2-0.3%. However, if

the ash content is higher (0.5% and over), the interval

from maintenance to maintenance is reduced and the

accumulation of ash increases by 2 or 3 times. This

results in lower heat output and an increased fan

rotation speed. We therefore recommend

checking and/or cleaning the flue gas passes

after 1,000 kg of pellets at the latest. (See

Figure 8 a+d).

Attention!

Devices that are not maintained in accordance with

our specifications must not be operated. Failure to

observe this point will invalidate all guarantee

claims.

As soon as you detect ash and clinker deposits in the

cold combustion pot, it must be cleaned. (See Figures 5

+6). If this is not done, the clinker will continue to

accumulate. Then the device will no longer be able to

ignite properly. Pellets can pile up in the combustion pot.

In extreme cases, this can reach all the way back to the

pellet chute. Backfire in the pellet container and

smouldering in the pellet tank might possibly result.

This will destroy your device and is not covered in

your guarantee.

Attention!

Before starting any cleaning work, the stove must be

cool down and set to "Off"! Once the cleaning work

is completed, the correct operating status of the

device must be re-established: Put the combustion

pot in correctly, close the combustion chamber

door.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haas-Sohn HSP1.17 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Haas-Sohn HSP1.17

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info