Bedienungsanleitung Haas-Sohn PALLAZZA 517.08 (Seite 11 von 36) (Englisch)

812048

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Important: Your HAAS+SOHN Pelletto pellet stove may

only be operated with standardised wood pellets with a 6

mm diameter.

You can identify good quality wood pellets by eye by:

smooth, shiny surface, uniform length, little dust. Wood

pellets of lower quality are characterised by: Lengthwise

and crosswise cracks, a high proportion of dust, different

lengths. Precise quality features may however only be

identified with suitable technical analysis equipment.

A simple quality test: Put a few wood pellets in a glass of

water:

Good quality: Pellets sink

Lower quality: Pellets float.

The use of lower-quality or unauthorised fuel adversely

affects the operation of your pellet stove and may in

addition lead to the lapse of the guarantee and the

associated product liability. Unauthorised fuels include

woodchips, straw and maize. Burning wood pellets of

poor quality leads to shortening of the cleaning intervals

and to increased fuel consumption, so the pellet tank

has to be filled more frequently.

Wood pellets are packed in plastic or paper sacks. To

ensure problem-free combustion of the wood pellets it is

necessary to dry the fuel as much as possible and to

transport and store it free from dirt. On contact with

moisture, pellets swell considerably.

When filling the storage container with wood pellets,

make sure that the pellet sacks do not come into contact

with the hot surfaces of the stove.

Two kilograms of wood pellets have about the same

energy content as a litre of “extra light heating oil.” In

terms of volume, 3 m3 of wood pellets are equivalent to

about 1,000 litres of heating oil. Variations in heat output

by the pellet stove are caused not only by the quality of

the pellets but also by the raw material of the wood (type

of wood).

7.2. Commissioning your pellet stove

The materials making up your pellet stove must

gradually get used to the heat generation. By careful

warming up you avoid cracks in the combustion

chamber plates, damage to the paintwork and warping

of materials. So do not set the target temperature too

high on the control unit (about 1.5°C to 2°C higher than

the current room temperature).

 Before commissioning, remove any stickers and any

accessories from the ash pan and the combustion

chamber. This also applies to any

transportation/handling securing materials.

 Check that the combustion chamber cladding is

attached to its fastenings. (This might have slipped

out

of its position as a result of the transportation or

installation of the stove).

 Check that the combustion pot fits perfectly in its

frame.

 Close the combustion chamber door.

 Fill the storage container with standard wood pellets

(Ø 6 mm).

 Insert the mains cable.

 Set the On-Off toggle switch to “1”.

 Once the toggle switch has been set to ON, the

control unit commences initialisation. This process

takes a few seconds.

 After initialisation, the Information screen appears –

press the right key (Menu) – move cursor to

Operating mode – press the right key (Select) –

select the desired operating mode with the cursor –

press the right key (Save).

Tip!!

Only when commissioning, place about 30

pellets in the burner. This will speed up the

ignition process.

General:

If the ignition phase could not be successfully

run i.e. no flame generation or the required

temperature could not be reached at the flue

gas thermosensor, then a safety shutdown is

initiated and an error message generated

(“Ignition phase target temp. flue gas not reached –

check burner – date and time”).

Correcting the fault:

Once the stove has cooled down, empty the burner and,

if necessary, clean it. Take care! There may still be

residual embers in the ash! Then press the left key on

the operator console repeatedly until the error message

appears – then press the right key of the operator

console (Clear) – now the Info screen appears – press

the right key (Menu) – move the cursor to Operating

mode and press the right key (Select) – the screen in

which the operating mode may be selected appears –

select desired operating mode with the cursor and press

the right key (Save). The stove begins the ignition

phase.

Note: Any smoke generation caused by further drying of

the paint stops after a short while. Please properly

ventilate the room where the stove is installed. However,

the paint does not contain any toxic vapours.

7.3. Selecting the operating mode

The control unit allows easy selection of operating mode

from the “Heating” and “Auto” weekly programme

modes.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haas-Sohn PALLAZZA 517.08 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Haas-Sohn PALLAZZA 517.08

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info