Bedienungsanleitung Haas-Sohn PALLAZZA-II 519.08 (Seite 4 von 33) (Englisch)

564778

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

 The pellet stove may not be installed in the open

air!

 Attention! The mains cable plug must remain freely

accessible after installation.

 The pellet stove may only be operated with standard

wood pellets (6 mm diameter). (See Section 7.1

“Fuel”).

 The protective grille located in the pellet container

must not be removed.

 Attention! The Pelletto stove may only be

operated with the tank cover closed.

 Placing non-heat-resistant materials or objects on

the stove or within the specified minimum distances

is forbidden. Here please note in particular that

during “Standby” operating status, the stove may

unexpectedly and unintentionally start heating when

the room temperature falls below the desired

temperature.

 Never use liquid fuels to ignite the pellet stove or to

revive existing embers.

 With the burning up of fuels, heat energy is

released, leading to strong heating of the heating

device’s surfaces (e.g. doors, door and control

handles, viewing window panels, side walls, front

wall, flue tubes). Touching these parts without

suitable heat protection gloves or a tool is to be

avoided!

 The device ignites by itself in “Standby” mode.

Because of the heat generated on the panel, make

sure that no-one who is unfamiliar with the operation

of the pellet stove is unsupervised in the room where

it is installed.

 Bring these risks to your children’s and guests

attention!

 In particular, any cleaning staff should be informed

and instructed regarding the possible unexpected

heating up of the stove.

 Placing non-heat-resistant objects on or near the

heating device (even when it is cold, since it can

ignite again by itself) is forbidden!

 Do not lay any laundry on the stove to dry!

 Clotheshorses for drying clothes and the like must

be positioned at sufficient distance from the heating

device – fire risk!

 When operating your heating device, it is forbidden

to work with highly flammable or explosive

substances in the same room or an adjacent one!

3. Installation of the pellet stove and connection to

the chimney

The packaging on your new pellet stove gives it optimum

protection against damage. Nevertheless, damage may

have occurred to the stove or to accessories in transit.

Please therefore check your stove after unpacking for

damage and completeness! Report any defects or

anything missing to your specialist stove dealer without

delay!

The packaging on your stove is by and large

environmentally neutral. The timber packaging is not

untreated. The timber, the cardboard and the films can

be taken without problems to your local recycling centre.

For the correct operation of your pellet stove it is

important that it stands horizontally.

The room temperature sensor that is located on the back

wall has a length of about 1.5 m and should be

positioned hanging free at the back.

Figure 1: Back connections

1 = Mains electricity socket

2 = OC overheat cutout

3 = Room temperature sensor

4 = Fume elbow 80 mm

5 = Outside air connection 40 mm

6 = Bottom of back wall

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haas-Sohn PALLAZZA-II 519.08 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Haas-Sohn PALLAZZA-II 519.08

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info