Bedienungsanleitung Haas-Sohn PALLAZZA-II 519.08 (Seite 12 von 33) (Englisch)

564778

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

Procedure:

Press "Quit" with the right button ✔ and the error

can be confirmed.

Look point 11 on page 22

6.4..9 Description – Key lock (child-safe)

+ - Menu

Aus

08:15

28°C

23°C

Activating the key lock:

 Hold the Menu key down for about 10 seconds

until “Key lock activated” appears on the display.

Deactivating the key lock:

 Hold the Menu key down for about 10 seconds

until “Key lock activated” is no longer shown on

the display.

7. Operating the pellet stove

The pellet stove may only be heated by adults. Make

sure that children are never left alone with the pellet

stove. (Do not leave the pellet stove unsupervised for a

long period). The pellet stove may only be used in

accordance with these operating instructions.

Please observe the safety instructions set out in Section

7.1. Fuel

The pellet stove may only be operated with “pellet” fuel.

With this fuel you have chosen CO2-neutral heating for

your home.

Pellets are made from wood waste from sawmills and

planing works and from wood collected from forestry

businesses. These raw materials are therefore of 100%

natural origin and are ground, dried and pressed into

“pellet” fuel without the addition of binding agents.

This fuel is standardised (e.g. DINplus, ÖNorm M 7135,

ENplus-A1.).

Important: Your HAAS+SOHN Pelletto pellet stove may

only be operated with standardised wood pellets with a 6

mm diameter.

You can identify good quality wood pellets by eye by:

smooth, shiny surface, uniform length, little dust. Wood

pellets of lower quality are characterised by: Lengthwise

and crosswise cracks, a high proportion of dust, different

lengths. Precise quality features may however only be

identified with suitable technical analysis equipment.

A simple quality test: Put a few wood pellets in a glass

of water:

Good quality: Pellets sink

Lower quality: Pellets float.

The use of lower-quality or unauthorised fuel

adversely affects the operation of your pellet stove

and may in addition lead to the lapse of the guarantee

and the associated product liability. Unauthorised fuels

include woodchips, straw and maize. Burning wood

pellets of poor quality leads to shortening of the cleaning

intervals and to increased fuel consumption, so the

pellet tank has to be filled more frequently.

Wood pellets are packed in plastic or paper sacks. To

ensure problem-free combustion of the wood pellets it is

necessary to dry the fuel as much as possible and to

transport and store it free from dirt. On contact with

moisture, pellets swell considerably.

When filling the storage container with wood pellets,

make sure that the pellet sacks do not come into contact

with the hot surfaces of the stove.

Two kilograms of wood pellets have about the same

energy content as a litre of “extra light heating oil.” In

terms of volume, 3 m3 of wood pellets are equivalent to

about 1,000 litres of heating oil. Variations in heat output

by the pellet stove are caused not only by the quality of

the pellets but also by the raw material of the wood (type

of wood).

7.2. Commissioning your pellet stove

The materials making up your pellet stove must

gradually get used to the heat generation. By careful

warming up you avoid cracks in the combustion

chamber plates, damage to the paintwork and warping

of materials. So do not set the target temperature too

high on the control unit (about 1.5°C to 2°C higher than

the current room temperature).

 Before commissioning, remove any stickers and

any accessories from the pellet tank and the

combustion chamber.

 Check that the combustion chamber cladding is

attached to its fastenings. (This might have

slipped out of its position as a result of the

transportation or installation of the stove).

 Check that the combustion pot fits perfectly in its

frame.

 Close the combustion chamber door.

 Fill the storage container with standard wood

pellets (Ø 6 mm).

 Insert the mains cable.

 Once the toggle switch has been set to ON, the

control unit commences initialisation. This

process takes a few seconds.

 After initialisation, the Information screen

appears – press the right key (Menu) – move

cursor to Operating mode – press the right key

(Select) – select the desired operating mode

with the cursor – press the right key (Save).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haas-Sohn PALLAZZA-II 519.08 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Haas-Sohn PALLAZZA-II 519.08

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info