Bedienungsanleitung Haas-Sohn PALLAZZA-II 534.08 (Seite 13 von 33) (Englisch)

564781

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

Tip!!

Only when commissioning, place about 30 pellets in

the burner. This will speed up the ignition process.

General:

If the ignition phase could not be successfully run i.e. no

flame generation or the required temperature could not

be reached at the flue gas thermosensor, then a safety

shutdown is initiated and an error message generated

(“Ignition phase target temp. flue gas not reached –

check burner – date and time”).

Note: Any smoke generation caused by further

drying of the paint stops after a short while. Please

properly ventilate the room where the stove is

installed. However, the paint does not contain any

toxic vapours.

8. Cleaning and maintenance work

The functioning of your device depends to a large extent

on regular expert maintenance. Because of the ash

accumulation resulting from the combustion of wood

pellets, constantly recurring cleaning and maintenance

work needs to be carried out. This will permit operation

to be as trouble-free as possible.

The frequency of maintenance in turn depends to a large

extent on the pellet quality (ash content). Quality pellets

have a low ash content of about 0.2-0.3%. However, if

the ash content is higher (0.5% and over), the interval

from maintenance to maintenance is reduced and the

accumulation of ash increases by 2 or 3 times. This

results in lower heat output and an increased fan

rotation speed. We therefore recommend

checking and/or cleaning the flue gas passes

after 1,000 kg of pellets at the latest. (See

Figure 8 a+d).

Attention!

Devices that are not maintained in accordance with

our specifications must not be operated. Failure to

observe this point will invalidate all guarantee

claims.

As soon as you detect ash and clinker deposits in the

cold combustion pot, it must be cleaned. (See Figures 5

+6). If this is not done, the clinker will continue to

accumulate. Then the device will no longer be able to

ignite properly. Pellets can pile up in the combustion pot.

In extreme cases, this can reach all the way back to the

pellet chute. Backfire in the pellet container and

smouldering in the pellet tank might possibly result.

This will destroy your device and is not covered in

your guarantee.

Attention!

Before starting any cleaning work, the stove must be

cool down and set to "Off"! Once the cleaning work

is completed, the correct operating status of the

device must be re-established: Put the combustion

pot in correctly, close the combustion chamber

door.

8.1. Cleaning the surface

Dirt on the upper surface of the stove may be cleaned

off with a damp cloth or if necessary with mild soapy

water. You are advised against using corrosive cleaning

agents and solvents since these might damage the

surfaces.

8.2. Cleaning the glass panel

To clean the viewing panel, you must first open the

stove door. Dirt on the glass panel can be removed with

a glass cleaner or with a damp sponge on which you

have sprinkled some of the wood ash present.

(Environmentally friendly).

Cleaning the glass panel may only be done with a

cooled down stove in the OFF operating mode.

8.3. Clean combustion chamber” function

instruction

Die The display on the operator console starts flashing.

(The backlighting switches on and off and the “Clean

combustion chamber” instruction appears).

The instruction to clean the combustion chamber refers

not just to the cleaning of the burner but also to the

cleaning of the entire combustion chamber with an ash

vacuum cleaner.

The process of the “Clean combustion chamber”

function looks like this:

The entire combustion chamber is to be cleaned with an

ash vacuum cleaner at intervals of no longer than 30

operating hours.

The process of the “Clean combustion chamber”

function looks like this:

The entire combustion chamber is to be cleaned with an

ash vacuum cleaner at intervals of no longer than 30

operating hours.

However, this instruction to clean the combustion

chamber (display flashing) does not trigger an error

message during Heating mode. But after the display has

started flashing, if the stove switches

back to “Standby” mode, the stove can no longer be

automatically ignited before the combustion chamber

has been cleaned.

To clean the combustion chamber, the stove has to be

switched to “Off” operating status.

If the combustion chamber is now cleaned, then the

“Clean combustion chamber” error message will

thereafter be cleared automatically. A precondition for

the automatic clearance of this error message is that the

combustion chamber door is open for longer than 60

seconds in “Off” operating status. This time is required

for cleaning the combustion chamber including the

burner thoroughly with an ash vacuum cleaner.

If the door is open longer than 60 seconds in “Off”

operating status, then the operating hours counter,

which is responsible for the “Clean combustion

chamber” instruction, is automatically reset to zero.

This reset of the operating hours counter occurs even if

the cleaning of the combustion chamber is performed

before the 30 operating hours have run provided that the

stove is in “Off” operating status and the door is open for

longer than 60 seconds during cleaning.

Haas-Sohn PALLAZZA-II 534.08 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Haas-Sohn PALLAZZA-II 534.08

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info