Bedienungsanleitung Haas-Sohn WARBURG (Seite 3 von 6) (Englisch)

812021

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Warning! The multi-fuel stove may not be used in

combined operation with air ventilation devices in your

house or apartment.

The operation of this stove is not compromised, if the

devices just circulate air within a room, or if the devices are

fitted with safety systems which automatically and reliably

prevent low pressure forming in the room in which the stove

is sited. It is essential that you make sure that you have a

sufficient supply of air for combustion by checking with

your master chimney sweep.

Heat energy is released by burning combustible materials,

which leads to the surfaces of the stove being heated up

strongly (the doors, door handles, the operating controls, the

transparent windows, the side walls, the front wall and the

exhaust flue). Avoid touching these parts without wearing

appropriate heat resistant gloves! A heat resistant glove is

provided with this multi-fuel stove.

Do not wear any loose or flammable articles of clothing

when adding fuel to your multi-fuel stove!

Make children aware of these dangers and keep them away

from the stove when it is producing heat.

If incorrect or damp fuels are used, then a chimney fire may

occur because of deposits in the chimney. Close all air

openings in the stove and inform the fire brigade. After the

fire in the chimney has been extinguished have the chimney

professionally examined for any cracks or leaks.

Warning! Never operate the multi-fuel stove without

water and never without a functional cold water supply

and the operation of the temperature limiting device and

the accompanying safety controls.

Otherwise there is a risk of an explosion leading to

irreparable damage!

3. Data for calculating the chimney dimensions

according to DIN 4705 Part 2

The data for calculating the chimney dimensions according

to DIN 4705 Part 2 can be found in the accompanying

device information sheet.

4. Installation and connection of the multi-fuel

stove

The packaging of your new multi-fuel stove provides the

optimum protection against damage. During transport

damage can still occur to your stove or its accessories.

Please examine your multi-fuel stove after you have

unpacked it for damage and completeness! Immediately

report any defects to your stove dealer!

Note: Draught deflector plates or similar which are loose or

have slipped out of their positions are not considered to be a

defect (see section 5.3: Using your chimney for the first

time).

The packaging of your multi-fuel stove is to a large extent

environmentally neutral. The wood of your packaging is not

surface treated and can be used as a fuel when chopped up

into small pieces. The cardboard and the film can be sent to

the local recycling centre without any problems.

4.1. Safe distances (minimum distances):

When installing your multi-fuel stove the officially

prescribed fire protection regulations must be strictly

followed. Ask your local master chimney sweep if you have

any questions about them.

The following minimum distances from flammable or

temperature sensitive materials (e.g. furniture, wallpaper,

wooden panelling) or from load-bearing walls must be

complied with (see diagram below):

A 20 cm to the rear wall

B 20 cm to the side walls

C 80 cm in the radiation area

In the radiation area (C) no flammable building components

or furniture should be placed within a distance of 80cm from

the transparent window. This distance can be reduced to

40cm if a radiation protection plate that is well-ventilated on

both sides is placed between the stove and the flammable

building components.

The minimum distances to flammable building components

and furniture are given on the specification plate and should

not be any less than these values.

With flammable or heat sensitive floor-coverings the device

must be placed on a non-flammable protective base plate

(e.g. steel sheet, glass). The minimum distances are then (see

diagram):

D 50cm

E 30cm (from the inner edge of the opening to the

combustion chamber)

We stock protective base plates as part of our accessories

programme. If necessary you can order them from your stove

dealer.

4.2. Connection to the chimney

For connecting the stove to the chimney a flue tube made

from 2mm thick steel tubing should be used.

The flue tube should be tightly and securely connected to not

only the exhaust gas connecting piece, but also to the

chimney. Tight and secure connection is also necessary

between the flue elements. It is essential to make sure that

the flue tube does not extend into the empty section of the

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haas-Sohn WARBURG Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Haas-Sohn WARBURG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info