Bedienungsanleitung Haier Dawn (Seite 5 von 233) (Englisch)

771631

Zoom out

Zoom in

Vorherige Seite

1/233

Nächste Seite

Operation

Clock set

Note:

Note: The distance between the signal transmission head and

the receiver hole should be within 7m without any obstacle

change-over wireless telephone is installed in the type

in receiving the signals, so the distance to the indoor unit

should be shorter.

Full display or unclear display during operation indicates the

batteries have been used up. Please change batteries.

If the remote controller can’t run normally during operation,

please remove the batteries and reload several minutes later

Hint:

Remove the batteries in case unit won’t be in usage for

a long period.

20. 10 ºC button

special heating set

function: 10 degree

heating maintaining

(valuable for RS)

18. buttonTIMER

23. SWING up/down button

24. SWING left/right button

19. buttonCLOCK

26. HEALTH AIRFLOW button

21. HEALTH button

28. CODE button

A-b yard

29. APPLY button

30. °F/°C button

25. SLEEP button

23 24

22. SMART button

Used to set SMART

operation. (This function

is unavailable on some

models.)

27. LIGHT button

Control the lightening and

extinguishing of the indoor

LED display board.

Press CLOCK button,

Press “+” or “-” to set

correct time.

Each press will increase or

decrease 1min. If the button is

kept pressed, time will change

quickly.

press APPLY, “AM” and

starts working.

1. SMART+SLEEP:When the light sensing function is enabled,

the appliance will be in the mode. If the appliance

detects that indoor light is weak (lower than the setting

value) for several minutes, the light sensing function

works automatically. If theappliance detects no movements

of people for 20 minutes , during which the light is weaker

than the setting value , it will enter the “SMART+SLEEP”

mode automatically. The appliance will operate as per the

sleep curve.(See the“SLEEP”function in Page 7).

Conditions to exit:

1) The appliance detects that the indoor light is stronger

than the setting value for 20 minutes.

2) The appliance is in the 8h “SMART + SLEEP” mode.

3) The “LIGHT SENSING” function is disabled.

When any of the above conditions is met, the appliance will

exit from the “SMART+SLEEP” mode. Once out of the

“SMART+SLEEP” mode, the appliance will operate under

the operation status initially set on the remote controller.

Note:1) This function is not available in the “AIR SUPPLY”

mode.

2) This function is not available in the “SLEEP”mode.

3) When it is in the "REMOTE SLEEP” mode or the

“TIMER”is on, the appliance will exit from this function.

4) Light sources like indoor lamps and TV’s LED

light,and frequent movement s of pets will affect this

function.

2. Press “HEALTH”+“HEALTH AIRFLOW” simultaneously can

set and cancel the “LOCK” function ( )

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haier Dawn Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info