Bedienungsanleitung Haier Flexis Plus 2021 (Seite 18 von 21) (Englisch)

771618

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

1.Insertfromoutsidetheroomcableintoleftside of thewall

hole, in which the pipe has already existed.

2. Pull out the cable on the front side, and connect the cable

making a loop.

When connecting the cable, conrm the terminal number of indoor and

outdoor units carefully. If wiring is not correct, proper operation can not

EHFDUULHGRXWDQGZLOOFDXVHGHIHFW

Insertthecablefromtheback side of the unit, then pull it out on the front side.

Loosen the screws and insert the cable ends fully into terminal block, then

tighten the screws.

Pull the cable slightly to make sure the cables have been properly inserted and

tightened.

After the cable connection, never fail to fasten the connected cable with the

wiring cover.

When connecting the cable after installing the indoor unit

When connecting the cable before installing the indoor unit

Note:

1. If the supply cord is damaged, it must be replaced by the manufacturer or its

service agent or a similar qualied person. The type of connecting wire is

H05RN-F or H07RN-F.

2.IfthefuseonPCboardisbrokenpleasechangeitwiththe type of

3. The wiring method should be in line with the local wiring standard.

4. After installation, the power plug should be easily reached.

5. A breaker should be incorporated into xed wiring. The breaker should be

all-pole switch and the distance between its two contacts should be not less

than 3mm.

T.3.15A/250VAC (Indoor).

To Outdoor unit

Connecting wiring

4G1.0mm

Code

indication Trouble description Analyze and diagnose

E14

Heat-exchange

sensor failure

Indoor EEPROM

error

Communication

fault between

indoor and outdoor

units

Indoor fan motor

malfunction

Operation halt due to breaking

of wire inside the fan motor;

Operation halt due to breaking

of the fan motor lead wires;

Detection error due to faulty

indoor unit PCB;

Indoor unit- outdoor unit signal

transmission error duetowiring

error;

Faulty PCB;

Faulty EEPROM data;

Faulty EEPROM;

Faulty PCB;

Faulty connector connection;

Faulty thermistor;

Faulty PCB;

Room temperature

sensor failure

The power source must be exclusively used for air conditioner.

In the case of installing an air conditioner in a moist place, please install

an ea

For installation in other places, use a circuit breaker as far as possible.

Pipe cutting is carried out with a pipe cutter and burs must be removed.

After inserting the are nut, aring work is carried out.

Power Source Installation

Cutting and Flaring Work of Piping

FlaretoolforR410A Conventionalaretool

Clutch-type clutch-type(Rigid-type) Wing-nut type (Imperial-type)

A 0~0.5mm 1.0~1.5mm 1.5~2.0mm

rth leakage breaker.

Lean Damage of are Partial Too outside

tcerrocnItcerroC

On Drainage

It becomes

high midway. The gap with the

ground is too small.

There is the bad

smell from a ditch

It waves.

The end is imm-

ersed in water.

Pleaseinstallthedrainhosesoastobedownwardslopewithoutfail.

Please don’t do the drainage as shown below.

Please pour water in the drain pan of the indoor unit, and

is carried out surely to outdoor.

In case that the attached drain hose is in a room, please apply heat

insulation to

Less than

5cm

conrm that

drainage

it without fail.

Crack

Indoor unit

Check Items for Test Run

Gasleakfrompipeconnecting?

Heat insulation of pipe connecting?

Are the connecting wirings of indoor and outdoor rmly

Is the connecting wiring of indoor and outdoor rmly xed?

Is drainage securely carried out?

Is the earth line securely connected?

Is the indoor unit securely xed?

Is power source voltage abided by the code?

Is there any noise?

Is the lamp normally lighting?

Arecoolingandheating(wheninheatpump)performednormally?

Is the operation of room temperature regulator normal?

Please kindly explain to our customers how to

operate through the instruction manual.

inserted to the terminal block?

Put check mark in boxes

Flare tooling die 1.Cut pipe 2.Remove burs

3.Insert the are nut 4.Flare pipe

On Drainage

Check for Installation and Test Run



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haier Flexis Plus 2021 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Haier Flexis Plus 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info