Bedienungsanleitung Haier HWM70-1203D (Seite 19 von 20) (Englisch)

650533

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

maintenance

troubLeshooting

TROUBLESHOOTING

The following circumstances do not mean there is a fault with the appliance. Contact the Customer Care Team when you have conﬁrmed

the problem after following the instructions below.

PROBLEM CAUSES SOLUTIONS

Washing machine fails to

operate.

¬ Poor connection to the power supply.

¬ Power failure.

¬ The washer door is not properly closed.

¬ Machine has not been switched on.

_ Check connection to the power supply.

_ Check the power supply.

_ Close the washer door properly.

_ Make sure the machine is switched on.

Washing machine cannot be

ﬁlled with water.

¬ The "Start/Pause" button is not pressed.

¬ Water tap is not turned on.

¬ Water pressure is less than 0,03 MPa.

¬ The inlet hose is kinked.

¬ Water supply failure.

¬ The program knob is not properly set.

¬ The washer door is not properly closed.

¬ The inlet hose ﬁlter is blocked.

_ press the "Start/Pause" button.

_ Turn on the water tap.

_ Check water pressure.

_ Check the inlet hose.

_ Ensure the water supply.

_ Set the program knob properly.

_ Close the washer door properly.

_ Unblock the inlet hose ﬁlter.

Machine is draining while

being ﬁlled.

¬ The height of the drain hose is below 80 cm.

¬ The drain hose is in water.

_ Install drain hose within 80-100 cm of height.

_ Make sure the drain hose is not in water.

Drainage failure. ¬ Drain hose is blocked.

¬ Drain hose end is higher than 100 cm above

the ﬂoor level.

¬ The ﬁlter is blocked.

_ Unblock the drain hose.

_ Make sure the drain hose end is lower than

100 cm above ﬂoor level.

_ Unblock the ﬁlter.

Strong vibration while

spinning.

¬ Not all transportation bolts have been removed.

¬ Washing machine is located on an uneven

surface or is not level.

¬ Machine load is over 8kg.

_ Remove all transportation bolts.

_ Make sure the washing machine is on

an even surface and levelled.

_ Reduce amount of laundry in the drum.

Operation stops before

completing wash cycle.

¬ Water or electricity failure. _ Check the power supply or water supply.

Operation stops for a period

of time.

¬ Washing machine gives an error message.

¬ Washing machine is in soaking cycle?

_ Check display codes.

_ Press the rinse hold button or the Start/pause

button again to cancel it.

Excessive foam in the

drum, which is spilled to the

distribution drawer.

¬ The detergent is not a low-foaming type or for

manual wash.

¬ Excessive use of detergent.

_ Check if your detergent is appropriate.

_ Reduce amount of detergent in the distribution

drawer.

Automatic adjustment of the

washing time.

¬ The washing program duration will be adjusted _ This is normal and doesn't affect the

functionality.

Spinning fails ¬ Unbalance of the laundry _ Add clothes or run a spinning program again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Haier HWM70-1203D Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info