Bedienungsanleitung Hama 11413 - 8 in 1 (Seite 2 von 44) (Alle Sprachen)

607793

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Universal Remote Control

Thank you for your decision for a Hama product.

Take your time and read the following instructions

and information completely. Please keep these

instructions in a safe place for future reference.

Function buttons (Models 4 in 1, 8 in 1)

1. LED indicator

2. Mode key for selection of secondary device

group (only 8 in 1 model: AUX,DVBT,CBL,AMP)

3. Device selection keys

4. Setup: Remote control settings

5. Vol+/Vol-: Volume control

6. Text ON: Switch on Teletext

Menu: Open device menu

7. Hold: Hold the current Teletext page

8. Number Keys 0-9

9. AV: selects external A/V sources

10. ◄◄ Rewind/red

► Play/yellow

►► Fast forward/blue

● Start recording

■ Stop/green

ll Pause/magenta

11. -/- -: Switch to two-digit channel numbers

12. Info: On-Screen information (if supported by

A/V device)

EPG: Electronic Programme Guide (if supported

by selected A/V device)

13. Text OFF: exits Teletext

EXIT: exits device menu

14. PROG+/PROG-:Programme selection up/down

15. Mute Switch

OK: Confirms a selection

16. Shift key

17. Power: ON/OFF

1. Explanation of the Note symbol

Note

► This symbol is used to indicate additional in-

formation or important notes.

2. Package Contents

- Universal Remote Control (URC)

- Code List

- This operating instructions

3. Safety notes

• Do not use the Universal Remote Control in mo-

ist or wet environments and avoid spray-water

contact.

• Do not expose the Universal Remote Control to

heat sources or direct sunlight.

• Do not drop the Universal Remote Control..

• Never open the Universal Remote Control. It

contains no user-serviceable parts.

• As with all electrical devices, keep the Universal

Remote Control away from children.

4. Getting started – installing the Batteries

Note

► Alkaline batteries are recommended. Use 2

„AAA“ (LR 03/Micro) type batteries.

► Remove the battery compartment lid on the

back of your URC.

► Check the required battery polarity and in-

sert batteries according to the “+/–” marks

inside the compartment.

► Close battery compartment lid.

Note: Code saver

► Any codes you have programmed remain

stored for up to 10 minutes while you re-

place the battery .Make sure you do not

press any buttons before you have placed

new batteries inside the remote control.

All the codes will be erased if a button is

pressed while there are no batteries in the

remote control.

Note: Battery saving function

► The remote control switches off automatical-

ly when a button is pressed down for more

than 15 seconds. This conserves battery

power if the remote control gets stuck in a

position where the buttons are continually

pressed down,such as between sofa cushi-

ons.

5. Setup

Notes

► To obtain a proper infrared (IR) transmission,

allways point your Remote control in the ap-

proximate direction of the device you want

to control.

► Press the “MODE” key to select the seconda-

ry device group :AUX, AMP, DVB-T, CBL (only

8 in1 Model).

► Press the Shift key to operate the blue func-

tion keys. The Shift function deactivates by

pressing the Shift key again, or automatically

after approx. 30 sec. without use.

► No entry for approx. 30 seconds will time out

the Setup mode. The LED indicator shows six

ashes and turns off.

► Each device type can be programmed under

any device key, i.e a TV can be programmed

under DVD, AUX, etc.

► If you want to control a device , it´s not pos-

sible while the Universal Remote Control is

in the Setup Mode. Exit the Setup mode and

select the device you want to control using

the device selection keys.

5.1 Direct Code Entry

Your Universal Remote Control Package contains a

code list. The code list shows 4-digit codes for most

A/V device manufacturers in alphabetical order and

grouped by device type (e.g. TV, DVD, etc.). If the

device you want to control is covered by the code

list, the Direct Code Entry is the most convenient

entry method.

5.1.1 Turn on the device you want to control

5.1.2 Press the SETUP key until the LED indicator is

permanently lit.

5.1.3 Select the device you want to control using

the device key (e.g. TV). A successful selection

is indicated by the LED with one ash follo-

wed by permanent light.

5.1.4 Check code list for brand and type of the

device you want to control.

5.1.5 Enter the corresponding 4-digit code using

the 0 – 9 keys. The LED indicator conrms

each entered digit via a short ash and turns

off after the fourth digit.

Note

► If the code is valid, it is saved automatically

► If code is invalid, the LED indicator ashes

six times and then turns off. Repeat steps

5.1.1 to 5.1.5 or use a different code entry

method.

5.2 Manual code search

Your Universal Remote Control is equipped with

an internal memory, which is preloaded with up to

350 codes per device type for the most common

A/V devices. You can zap through these codes until

the device you want to control shows a reaction.

This might be that the device you want to control

switches off (POWER key) or changes the channel

(PROG+/PROG- keys).

5.2.1 Turn on the device you want to control

5.2.2 Press the SETUP key until the LED indicator is

permanently lit.

POWER

SETUP SHIFT

MENU EPG EXIT

VOL-

PROG+

PROG-

123

456

789

AV -/--

VOL+

DVDSAT

VCR

4in1

Art.Nr.: 00011412

MODE

POWER

AUX

SETUP SHIFT

MENU EPG EXIT

DVBT CBL

AMP

VOL-

PROG+

PROG-

123

456

789

AV -/--

VOL+

DVD

SAT

VCR

8in1

Art.Nr.: 00011413

Operating Instruction

Hama 11413 - 8 in 1 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info