Bedienungsanleitung Hama 12083 - 3 in 1 (Seite 4 von 11) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

607795

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

Universal Remote Control

Function buttons

1. LED display

2. Power: ON/OFF

3. Device selection buttons

(TV, DVD, STB)

4. Setup

5. VOL+/VOL–:Volume control

6. Text ON:Switch on TeletextMenu:Open

device menu

7. Hold:Hold the current Teletext page

8. Number keys 0-9

9. AV:Switch to an external device

10. E Rewind / red

B Play / yellow

F Fast forward / blue

I Start recording

K Stop / green

J Pause / magenta

11. -/--: Switch to two-digit channel

numbers

12. Info: Information about the station

(depending on device)

EPG: Display Electronic Programme Guide

(depending on device)

13. Text OFF: Switch off Teletext

EXIT: Exit device menu

14. P+/P–:Programme selection

15. H Mute switch

OK: Confirm your entry

16. Shift: For the blue function buttons, e.g.

OK When the Shift button is pressed, the

LED is illuminated. The Shift function is

then active for approx. 30 seconds and

automatically switches off again.

Alternatively, it can be switched off at any

time by pressing the Shift key again.

General

This universal remote control is one 3 in 1

remote control and can operate following

device types: TV, DVD, STB. (e.g. DVD-

recorder/Player,

video recorders, boosters, tuners, etc.).

The lettering of the keys does not describe

the device type to be programmed, it is used

therefore only for the easier overview.

Note down please the codes of your devices

which you used for the programming. If the

codes should be e.g. to a battery change no

more not stored, you can program the remote

control so more quickly.

They must program a four-digit device code

to a source key (TV, DVD, STB) for every

device which you

would like to operate with the universal

remote control.

Video recorder: for the code search please

inserted a tape.

Programming device codes

Entering device code after code set

The codes of the corresponding devices are

the code list, to take that is enclosed in this

operating manual.

• Turn on the device manually.

• Hold the key setup (4) pressed for approx.

3 seconds until the red LED (1) lights up

permanently.

• Press the source key (3) (TV, DVD, STB)

shortly.

• You distribute the corresponding four-digit

code then the code table one.

• To the conﬁrmation of every keystroke the

red LED (1) goes out shortly.

• If the code input was valid, the red LED (1)

goes out according to the input of the last

place.

• Press SHIFT (16) brieﬂy and then OK (15)

to save the code. The LED (1) brieﬂy goes

out.

• Brieﬂy press the Shift (16) key.

• An invalid code was entered, the red

LED (1) ﬂ ashes for three seconds before it

goes out. Should the device not reacts;

you repeat the programming where

appropriate with another code. Please try

out all codes indicated for your brand.

• Select the code which all available

commands of your remote control react to

correctly.

• You should not have also any success in

this way, then you attempt it with that one

„search run automatic in the chapter“

described search method.

Manual code search run

• Turn on the device manually.

• Hold the key setup (4) pressed for approx.

3 seconds until the red LED lights up

permanently.

• Press the source key (3) (TV, DVD, STB)

shortly.

• You press repeatedly the key POWER (2)

after each other (this can be up to 350

times), only at VCR (Video recorders) asks

the key P+ (14) or P- (14)

• to the device that is supposed to be

operated, off, or changes the channel or

reacts correspondingly. The code-search

is begun with the code number currently

stored on the cluster.

• Press SHIFT (16) brieﬂy and then OK (15)

to save the code. The LED (1) brieﬂy goes

out.

• Brieﬂy press the Shift (16) key.

• Due to the extensive number of different

possible codes, up to 350 possible codes

are preset per device type. In individual

cases, it may be possible that only

the most common main functions are

available. The procedure described may

be unsuccessful for some special device

models.

Automatic search run

If your device does not respond to the remote

control although you tried out all codes

performed for your device type and the

corresponding brand, you attempt it with the

automatic search run. Through that you

can ﬁ nd also such codes of such brands

which are not performed in the device code

list.

• Turn on the device manually

• Hold the key setup (4) pressed for approx.

3 seconds until the red LED (1) lights up

permanently.

• Press the source key (3) (TV, DVD, STB)

shortly.

• Focus the remote control on the device

and press the key P+ (14) once shortly.

• If the device does not have any

program-function, you press the key

POWER (2) instead of the P+ (14).

• The remote control starts the code

search after 6 seconds and sends in the

1 second’s clock pulse (see also next

section) after each other all codes. At

every sending the red LED lights up.

• As soon as the device responds to the

remote control, press SHIFT (16) and then

OK (15). Brieﬂy press the Shift (16) key. If

you do not press OK in time, press PROG-

(14) to return step-by-step to the code

where the device responded.

• To stop searching, press SHIFT (16) and

then EXIT (13).

• Brieﬂy press the Shift (16) key.

g Operating Instructions

Hama 12083 - 3 in 1 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info