Bedienungsanleitung Hama 20305 - Easytip M1 (Seite 4 von 10) (Englisch)

607802

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Deutsch

The 5-second rule

universal remote control initially needs your assistance to work properly.

All programming is based on the 5-second rule: every step in these instructions

must be completed within 5 seconds after the previous step. Otherwise, the

remote control returns to standard operating mode. This rule ensures that your

remote control is not inadvertently reprogrammed by another user.

Quick setup

Step 1 Insert the batteries (correct position is indicated at the base of the

battery slot).

Step 2 Select the device that you wish to control with your universal remote

control by turning the disk until the arrow points to the desired device,

(e.g. TV). (only for M5)

Step 3 Switch on your device (to programme the remote control for the TV

set, ensure that the television shows a picture).

Step 4 Press the key and keep it pressed until the LED flashes twice in

quick succession. (after approx. 2 seconds).

Step 5 Within 5 seconds of seeing the 2 flashes above, enter the 4 digit code

indicated for your device in the separate code list book.

Step 6 After you have entered the code the LED will flash twice, indicating

that the code has been accepted by your universal remote control.

This does not necessarily mean it is the correct code for your model of

device.

Step 7 Press the key to check whether your universal remote control is

working properly. If your device is thereby set to standby mode, check

all other functions of the remote control. If certain functions are not

available or not working properly, refer to the next code in the list and

repeat the programming procedure from step 3.

Step 8 Please keep this booklet in a safe place for future use!

Tips If your device does not respond to any of the code numbers:

Q. None of the code numbers worked?

A. This might be because more than 5 seconds lapsed before you entered the

code or because you input an invalid code number In this case, check that

you have entered the correct 4-digit code or repeat the programming

procedure with the next code in the list whilst observing the 5 second

programming rule.

Q. My brand of TV is not listed in the code book?

A. Do not worry, simply read the section entitle “Automatic code scan”.

Programming for AUX devices (only M5)

The AUX option allows you to control an additional device with your universal

remote control.

By positioning the disk to point to DVD/AUX, you have the option to control a

second TV set, video recorder or SAT receiver instead of a DVD player.

To program your remote control for a second TV set, please proceed as

described in the programming instructions for television sets. However, you

must ensure that the rotary pointer is positioned at DVD/AUX.

For programming, please following the above instructions for quick setup.

PLEASE NOTE!

With manual code entry, all codes (TV, VCR, SAT and DVD) are permitted for

selection DVD/AUX. However, the automatic code scan for DVD/AUX only

searches for DVD codes.

USER MANUAL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hama 20305 - Easytip M1 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hama 20305 - Easytip M1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info