Bedienungsanleitung Hama 20310 - Easytip S2 (Seite 2 von 4) (Englisch)

607805

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Deutsch

Easy programming for the control of your TUNER

(RADIO)

To programme the remote control to operate your TUNER, proceed as

described for the CD PLAYER but using the key instead of the CD key.

Please ensure that you refer to the codes listed under the TUNER section and

not the CD PLAYER section.

Easy programming for the control of your TAPE

RECORDER (TAPE DECK)

To programme the remote control to operate your TAPE RECORDER, proceed

as described for the CD PLAYER but using the key instead of the CD key.

Please ensure that you refer to the codes listed under the TAPE section and not

the CD PLAYER section.

Easy programming for the control of your AMPLIFIER

To programme the remote control to operate your AMPLIFIER, proceed as

described for the CD PLAYER. Complete steps 1 to 10, using the key on

your remote control. Please ensure that you refer to the codes listed under the

AMPLIFIER section and not CD PLAYER section.

Code scan

If programming using the codes in the enclosed list failed to work then you

must next try the automatic code scan.

A. Ensure that the remote control is equipped with 2 new batteries (see step

one of easy programming procedure).

B. Switch on your TV SET. When using the automatic scan function for the

VCR, DVD, CD or TAPE, switch on your device, insert a video tape, DVD,

CD or tape cassette and put the unit into ‘Play mode’ i.e, the VCR tape etc

is running.

C. Press the key of your remote control for approx. 4 seconds until the

LED flashes twice.

D. After seeing the 2 flashes and within 5 seconds, enter the code .

After entering the code the LED will flash twice indicating that the code has

been accepted

E. Press and hold the key until your TV switches off. Please note that this

process might take up to 15 minutes. During the automatic scanning you

can remove your finger or change hands provided it is replaced within 8

seconds. If left off of the key for more than 8 seconds then the remote will

revert back to its normal mode. If your TV switches into Stand-By mode

during the automatic process then immediately remove your finger from the

key and then press and release the key until the LED flashes

twice, this will then store the code that the remote has found

F. In some cases during the automatic scanning search the remote control

might find several codes that appear to operate your TV etc, however, if

some of the buttons fail to work properly then it’s possible the remote has

found a partially compatible code. In such cases you will need to restart the

automatic scanning process (steps B. to F.) until a better code is found.

Please note that once the automatic process is restarted, the remote

continues from the last stored code and not at the beginning of code

database.

• To complete a code scan for the VCR, DVD, CD or TAPE, follow the

procedure above but use the key and not the key

• To complete a code scan for the TUNER, follow the procedure above but

use the key

AMP

TAPE

TUNER

USER MANUAL

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hama 20310 - Easytip S2 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hama 20310 - Easytip S2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info