122758

Hama 40081 1 in 1 Seite 4

4
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
7
d Bedienungsanleitung
6
g
Operating Instruction
Code Set Up
A Set Up by brand code:
According to the attached Device Brand
Code List, fi nd out the code of the device
brand and device code that you want to
control. For example, you can fi nd codes
for SONY TV: 010, 011, 028, and 030… Then
follow the steps as below.
a. Press and hold the [SET] key. Then press
the device key that you want to control,
such as [TV].
b. The LED will be on at moment. Then
release the pressed both keys.
c. Enter in the 3-digit Device Code (for exam
ple: code 010 under SONY TV).
d. If the entered Device Code is correct, the
LED will be off automatically, then gone
to step e. If it is incorrect, the LED will blink
twice and keep being at set up mode, then
return to step c.
e. Try if keys on remote control work or not.
If none key works or some key work but
most keys work improperly, please try
other codes in the same brand (for
example: code 028,030 ...under SONY TV),
repeat step a-e till you fi nd one code
which work good enough.
Remark: In the process of setup, if you want
to quit from setup mode, please press device
key. (If no key pressed in 10 seconds, the
remote control will leave the set up mode
automatically.)
B Set Up by Manual Search:
After you have set up by device brand
code several times, the remote control still
doesn‘t work (i.e. The device still can not be
controlled by this remote control), or you can
not fi nd the correct code in the Device Brand
Code List, you can use „Manual Search” to
fi nd out the reactive Code:
a. Power on the device that you want to
control.
b. Press and hold the [SET] keys. Then press
the device key in remote control, such as
[TV], etc
c. The LED will be on at moment. Then
release the pressed keys.
d. Point the remote control to the device,
strike the [POWER] key. the remote control
enters into” Manual Search” mode and the
LED keeps fl ashing.
e. See if device reacts or not. If it works, turn
to step f; If not, repeat step d every 1
second.
f. Test other keys. If keys work well enough,
press the device key to quit from the
search mode. If most keys don‘t work well
enough, repeat step d-f to fi nd the best
code.
Remarks:
• Whenever you want to leave or change
search mode, press the device key to quit,
and the LED will turn off.
• In the Manual Search Mode, besides the
[POWER] key ([POWER] key, all other keys‘
function can be checked normally. That is
to say you can test other keys without
leaving Manual Search mode. It will leave
Manual Search mode automatically if no
key pressed in 30 seconds.
• You may use the SET key to change the
search direction from forward to backward
or from backward to forward.
C. Set up by Auto Search:
This search is similar to Manuel
Search except it transmits power signal
automatically instead of manually pressing
the power key during the search:
a. Power on the device you want to control.
b. Press and hold [SET] key, in the meantime,
press and hold the Device key that you
want to control.
(for example: TV) for more than 3 seconds
and then release them, the auto search
begins. The remote control enters into
Auto Search, LED fl ash, and remote control
transmit power signal every 2.0 second
automatically.
c. See if device react or not, once the device
reacts, press any key (except SET key) to
stop the search.
d. Test if other keys work well enough. If
most keys work not good enough, Auto
Search again to fi nd next reactive code
and try until you fi nd the best code.
Remark:
a. You must point your remote control to the
device that you want to control during
Auto Search.
b. Whenever you want to leave Auto Search
mode, press any key (except SET key) to
quit, and the LED will be Off. The search is
over.
c. When remote control search through all
codes (about 10 minutes), then the remote
control will quit from Auto Search process
automatically.
d. In case of you did not stop the search on
time when device reacted, you may use
the Manual Search to search back to fi nd
the passed code.
D. Set up byDevice Code Display
The device code is a 3-digit number and any
one of the 3 digits can be indicated:
1. Strike the device key which code no. You
want to display.
2. Press and hold the [SET] key, in the mean
time press the digit that you want to
display, such as 1,2,or3.
3. Release the both pressed keys
4. Count the times the LED blinks, and the
blinking time is the digit. If there is no blink,
the digit is zero.
For example: for code 138
SET+1 (fi rst digit): LED blinks 1 time
SET+2 (second digit): LED blinks 3 times
SET+3 (third digit): LED blinks 8 times
Reset
Use the Reset function to erase all the set
up data.
1. Press and hold the [SET] key.
2. Then press and hold the [0] key for more
than 3 seconds.
3. Then release the both pressed keys, the
LED will blink twice then off, your remote
control got reset.
… 4 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

hama-40081-1-in-1

Suche zurücksetzen

  • Brauch Beschreibung von 00004628 von hama fehrnauslöser für handy Eingereicht am 28-6-2019 10:52

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hama 40081 1 in 1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info