Bedienungsanleitung Hama 40098 - 8in1 (Seite 7 von 30) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

607816

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

You put the initial remote control and yours

40098 so there, that the send/receiver diodes

of the two Remote controls lie against each

other. Pay attention also to the regular height

direction of the two diodes. Guarantee that

the distance is about 2,5 cm (Thumb width)

between the 2 remote controls.

Copying of the keys

• Hold the key setup (16) pressed for approx.

3 seconds until the red LED lights up

permanently.

• Making key SETUP (16) go.

• Once the source key (3) (TV, STB, CBL,

AUDIO, AUX, VCR, CD, DVD) the key goes

out and shines again on.

• Pressing the key LEARN (18) once.

• To press the key of yours 40098 once,

under which one you copy the keys of the

original-remote.

• To hold the key of the original remote

control to be copied pressed, the red

LED goes out and again lights up (2 to 3

seconds). With an error ﬂ ashes the red

LED 3 seconds long, stays, however, in the

learning-mode. You attempt it once again

or change to another key.

• Repeat the procedure for the other keys

from step 5.

• Press the key SETUP (16) if all wanted keys

are copied.

• The red LED goes out.

Recommendations

• Do not move the remote controls during

the process

• You guarantee, that it during the room light

not around ﬂ uorescent tubes or energy

saving-lamps act since these sources of

light can cause troubles and inﬂ uence the

copy.

• The 2 remote controls must be away over a

meter of every source of light.

• Avoid the copying of the codes of the keys

V+; Of- and as well as the playing keys‘ (5),

because according to

The codes of these keys do absolutely not

control remote control the same devices.

• If the memory of yours 40098 is full, the

red LED ﬂ ashes for 3 seconds. Then it is

not more possible, to copy other codes

without carrying out some accrued

liabilities.

• If you copy a key, it is possible that the red

LED ﬂ ashes weakly. Let in this case

the key not rid and you wait, to which

ﬂ ashing stops.

Tips:

• The batteries of the 2 remote controls must

be in good repair; exchange it possibly.

• They can not copy any keys among

following keys: LEARN, SETUP,

• All keys under a mode are put out, when

a four-digit code under this mode is input

(also for the direct input of a code, the

search of a code or a brand).

Delete of all copied keys

• Hold the key setup (16) pressed for approx.

3 seconds until which red LED lights up

permanently.

• Making key SETUP (16) go.

• Pressing the key LEARN (18) twice. The red

LED goes out and lights up again.

• Pressing the key SETUP (16) that red LED

goes from once.

• All copied keys are will be deleting.

Normal use

After you have carried out the programming

of your remote control for yours audio/video

device, the remote control works in the most

common primary functions as the original

remote control of the respective device.

Focus your remote control on the wanted

device and press the corresponding source

key. The red LED will light up shortly.

They activate the functions now through

pressing of the corresponding function key of

your universal remote control.

At every keystroke the red LED lights up

shortly.

Possibly every function of your original

remote control is not directly available on the

universal remote control.

In particular near newer devices it is possible

that the functions are ﬁ rst of all put aside or

not at all available among other keys than

expected.

With the AV Taste you choose usually the

AV input of the TV set for e.g. the STB

receiver or the video recorder.

Special functions

„electronic program“

The key EPG (13) corresponds to the function

„Electronic Program Guide“ and has different

functions, depending on which device this

is used.

At STB - or VCR - codes keep you up the key

a programming carry out, provided that

your video recorder about a SHOWVIEW

- function.

“Punch through”

The punch through function lets you execute

speciﬁ c functions on a device type other

than the one that is selected. These are the

volume, mute, and playback functions.

When the remote control is set to AUDIO,

AUX, VCR, DVD, or CD mode, the Volume (7)

and Mute (17) buttons control the TV device

(provided the other devices do not have their

own volume control).

In TV mode or another mode without

playback functions, the Play, Pause, Stop and

(where applicable) Record buttons control

a connected video recorder, DVD player,

or DVD recorder. The controlled device is

always the last selected device.

By default, the universal remote control is

set so that the volume and mute functions

automatically control the TV set when a

source button for a video device (DVD, video

recorder, etc.) is being pressed.

Programming volume/mute to a different

device type

• Press and hold the Setup (16) button

for approx. 3 seconds until the red LED

remains lit.

00040098bda.indd Abs1:12-Abs1:1300040098bda.indd Abs1:12-Abs1:13 08.10.2009 10:24:55 Uhr08.10.2009 10:24:55 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hama 40098 - 8in1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info