Bedienungsanleitung Hama EWS2020 - 92651 (Seite 7 von 34) (Deutsch, Englisch, Holländisch, Französisch)

607471

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

AND 3 BUTTONS ON THE REAR SIDE

1. [ °C/°F ]

Toggle the temperature unit °C <- -> °F

2. [ UNIT ]

Press to toggle the pressure unit. (hPa/mb -> inHg)

3. [ MODE ]

Press & hold 2 seconds to enter backlight color setting

mode.

SLIDE SWITCH [ BACKLIGHT ] ON THE REAR SIDE TO

SELECT THE BACKLIGHT MODE

Power Supply

Slide

switch

position

Battery

Only

Battery

& Adapter

Adapter

only

Auto Wave hand in front of the

IR sensor to activate backlight

for 5 seconds

OFF Disable the backlight function

ON Wave hand

in front

of the IR

sensor to

activate

backlight

for

5 seconds

Backlight always on

GETTING STARTED

This Weather Station was designed for easy set up.

For best operation, the following steps are required to be

done in the proper sequence.

1. Insert batteries for main unit before doing so for the

sensor units.

2. Receiving unit cannot be set manually until the wire-

less remote sensor unit registration procedure has

been completed.

3. Position the remote unit and main unit within effective

transmission range, which, in usual circumstances,

is 250 feet.

Although the remote unit is weather resistant, it should

be placed away from direct sunlight, rain or snow.

BATTERY INSTALLATION FOR MAIN UNIT

1. Turn the metal nut anti-clockwise on the bottom of the

unit to open and release the battery compartment;

2. Insert 4 AA size 1.5 V alkaline battery as indicate by the

polarity;

3. Push the battery compartment back, turn the metal nut

clockwise to lock;

NOTE: Replace the batteries when the low battery indi-

cator appears on the top-right corner of the LCD.

WIRELESS REMOTE SENSOR REGISTRATION

PROCEDURE

1. Insert x4 AA batteries ﬁ rst to the main unit, the outdoor

temperature display shows “- -” . – While the wave

icon will keep blinking for 2 minutes indicate unit is in

sensor searching mode.

2. In a second step, insert the x2 AAA batteries for

the sensor unit. The LED on the front panel will start

ﬂ ashing at a rate of one time per around 2 seconds

indicates channel-1 is in use.

3. While the LED in the sensor unit is ﬂ ashing, press once

the [ CH ] key will change the sensor channel setting

to 2. Keep toggle on [ CH ] key can change channel

setting up to 5. The LED is blinking at a frequency to

indicate the channel setting. i.e. continuous blinks

2 times indicate channel-2 is selected.

NOTE: If user does not press any key for 10 seconds,

it will exit the channel setting mode and transmit

the RF signal. The main unit will register the

temperature reading.

(If the transmitter has the LCD display, the °C/°F key will

toggle the temperature unit on the LCD.)

REMOTE CHANNEL AUTO-SCROLLING

This device is equipped with an auto-scroll function.

While the auto-scroll function is set, the unit will

automatically cycle to display temperature of each

remote sensor for 6 seconds.

1. To retrieve manually the speciﬁ c sensor temperature

reading, press CHANNEL key until desired channel

number is displayed.

2. To enable auto-scroll function, use CHANNEL button to

select channel 1, 2, ... until auto scroll icon appears on

the left hand corner of the 3rd line display.

H. Auto scroll indicator

The animated rolling arrow icon is shown to indicate

the auto scroll of 5 different remote channel.

I. Outdoor maximum/minimum indicator

Indicates the maximum/minimum outdoor temperature

is displayed

J. Remote sensor battery low indicator

Appears when the batteries of the remote sensor are

running dry and the temperature measured by this

sensor is no longer reliable. The user must change the

batteries at once.

K. Barometric history indicator

Indicates the recorded air pressure reading in the past

24 hours

L. Barometric pressure window

Displays the barometric pressure reading in mb hpa or

inHg.

Barometric pressure chart

Shows the barometric pressure trend chart for the

past 24 hours

N. Moon phase

The animated running moon phase will pause for

5 seconds in place of current moon phase.

O. Sun position and Moon position

Sun rises from the east (E) and goes down in the west

(W) everyday. This weather station can calculate the

different sunrise, sunset, moonrise and moonset time

according to the input city and diagrams the sun and

moon position in a day at 3 hour interval.

P. Sunrise and Sunset time

Shows the exact sunrise time of a pre-set city in a

speciﬁ c day. Press [ CITY ] button once to toggle to see

the sunset time.

Q. City name

Abbreviation of a city name in Europe. The user must

set to his own located city before start to use this

weather station to have the correct sunrise, sunset

time & moon phase.

R. Clock window

Display current time, current time and weekday, calen-

dar or alarm time

S. Radio reception signal

Indicates the condition of DCF77 radio controlled time

reception

T. Alarm on icon

Appears when alarm is activated

DESCRIPTION OF BUTTONS

Sculpture has 7 major function buttons on the edge

1. [ MEMORY ]

Toggle to view the Max/Min reading of the indoor

temperature/humidity & remote temperature.

Press & hold 2 seconds to clear indoor temperature/

humidity memories or remote temperature records.

2. [ CHANNEL ]

Select among channel 1, 2, 3, 4, 5 or to enter auto

scroll mode.

Press and hold 2 seconds to activate or deactivate the

sensor searching mode.

3. [ HISTORY ]

Press to view the past 24-hour barometric readings.

Press and hold 2 seconds to enter the altitude adjust-

ment mode.

4. [ ]

Press once to increase the date to view the MOON

PHASE status, Sunrise and Sunset time of a speciﬁ c

day in Day-Month-Year (or Month-Day-Year depends

on the date format setting).

Press once to increase the setting in CLOCK, CALEN-

DAR or ALARM setting mode Press & hold 2 seconds

to manually activate or deactivate the radio controlled

function.

5. [ ]

Press to decrease the date to view the MOON PHASE

status, Sunrise and Sunset time of a speciﬁ c day in

Day-Month-Year (or Month-Day-Year depends on the

date format setting).

Press once to decrease the setting in CLOCK,

CALENDAR or ALARM setting mode.

Press once to arm or disarm the daily alarm under

alarm display mode.

6. [ CITY ]

Press once to toggle between the sunrise and sunset

time of a pre-set city in a speciﬁ c day.

Press and hold 2 seconds to enter city setting mode,

use [ ] and [ ] to select the abbreviation country

name and then city name according to the list in the

appendix, press [ CITY ] to conﬁ rm.

Use [ ] and [ ] to select the DST (Daylight Saving

Time) “ON” or “OFF”, press [ CITY ] to conﬁ rm.

7. [ CLOCK ]

Toggle amongst display for Clock-Sec (HR-MIN-Sec),

Clock-day (HR-MIN-Weekday), Calendar (Date-Month-

Year), alarm time and repeat…

00092651bda.indd 12-13

19.06.2009 11:09:40 Uhr

Hama EWS2020 - 92651 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info