Bedienungsanleitung HammerSmith M24977 BionicBurner (Seite 6 von 24) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch)

813567

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

21. Unplug the power cord immediately if faults arise during operation,

after use, and before cleaning.

22. Never use or touch the device or plug with wet hands.

23. Never immerse or clean the device under water. Always protect the

device against moisture. If the device falls into water, remove the plug

from the mains immediately! NEVER reach into the water while the

device is still connected to the mains!

24. RISK OF BURNS! Some parts of the device get very hot during use -

never touch hot areas!

25. NEVER point the hot air stream at people or animals.

26. Never touch the heat shield or nozzle during operation.

27. DANGER TO LIFE DUE TO FIRE AND/OR EXPLOSION!

a. Only for outdoor use. Never use in a garage or locations where liquid

fuels or highly ﬂammable materials may be stored or used.

b. Do not use in the vicinity of easily ﬂammable substances or gases.

c. Never direct the hot air stream at ﬂammable objects

(e.g. gas bottles). Always keep away from sources of ignition.

d. Do not smoke during use.

e. Keep out of reach of children.

28. Protect from extended exposure to sunlight and frost.

29. FIRE HAZARD! Dry plants, grasses, pine needles, leaves and wood can

catch ﬁre. Observe the treated plant for a while after application. It

could take some time before the plant catches ﬁre.

30. In the event of an unexpected ﬁre, make sure that there is no danger to

yourself, and then extinguish the ﬁre with a suitable ﬁre extinguisher.

Replacing cables and plugs

If the power cord of this device is damaged, contact our customer service (information can be found on the

back of this manual).

CONNECTION TO THE POWER SUPPLY

This device is equipped with a cable clamp that prevents the power cable from coming into contact with the

hot parts of the device.

NOTE: Always use the cable clamp. Failure to use the cable holder can damage the device and/or the

power cord.

USING THE CABLE CLAMP (#2)

Push the cable through the opening on the handle. Form a loop with the cable.

Route the cable around the cable clamp, and draw the cable tight.

BEFORE FIRST USE

Remove any packaging material. Dispose of the packaging material. Place all components included in the

delivery in a safe place. Check whether all parts are included as stated in the scope of delivery. If parts are

missing or faulty, please contact our customer service (contact details can be found on the back of this

manual).

ASSEMBLING THE EXTENSION POLE & HANDLE (# 3)

When you receive delivery of the device, the extension pole and handle are not yet assembled. To

assemble, proceed as follows:

1. Slide the extension pole into the fastening ring at the end of the device. Align the arrow mark on the

extension pole with the „open lock“ symbol on the fastening ring.

2. Push the extension pole into the fastening ring until the pole is in place.

3. Now turn the bar anti-clockwise until the arrow mark on the handle aligns with the „closed lock“

symbol on the fastening ring.

MOUNTING THE GUIDE WHEELS (#4)

1. Unscrew the holder for the guide wheels so that you can easily insert the wheels onto the guide rail at

the rear of the device.

2. Place the holder in the guide rail and slide the holder down towards the nozzle. Make sure that the cable

points towards the handle and lies behind the guide wheel holder.

3. Now tighten the holder using the side wheel.

4. SELECTING THE POSITION: You can choose between 3 positions. The guide wheels can click into 3

diﬀerent pre-set positions, and can be ﬁxed using the side wheel.

USE

GETTING STARTED

1. Before use of the device, attach the extension pole with handle as described above.

2. Secure the cable using the cable guide and cable clamp.

3. Attach the desired attachment as described in the section „Changing attachments“.

4. Connect the power cord.

Switching on:

1. Point the hot air nozzle with the desired attachment away from the body.

2. Slide the on/oﬀ switch into the desired position. You can choose between 2 settings:

- Position I - 60°C (cooling)

- Position II - 650°C (weed killing, paint removal, grill lighter - nozzle optionally available)

The air volume in both positions is 500l/min.

CHANGING ATTACHMENTS (#5)

DEVICE MUST BE SWITCHED OFF, DISCONNECTED FROM THE MAINS, AND COOLED!

1. There are 2 dot markings on the left and right of both attachments.

2. Align these with the guide rail on the hot air nozzle.

3. Slide the attachment into the guide and lock the attachment in an anti-clockwise direction. Make sure

that the attachment is securely locked in place.

CLEAR WEEDS (LEVEL 2) - CONE NOZZLE or CREVICE NOZZLE

1. Slide the On/Oﬀ switch to position II. Allow the device to heat up for approx. 45 seconds. Make sure that

you do not allow the nozzle to rest on sensitive surfaces such as wood, as this could lead to scorch marks.

2. Hold the conical or crevice nozzle over the weeds for at least 5 seconds. In the case of stronger weeds

or plants with thick, deep roots (e.g. dandelions) increase the duration of application. During this

process, the cell structure of the weeds is destroyed. This usually kills the weeds within 24 hours. It

is not necessary to completely burn the weeds. A few seconds are suﬃcient - even if the visible part

of the weed still appears green, this is completely normal and does not represent a shortcoming. The

eﬀect will be visible in the next few hours.

3. For eﬃcient treatment, the nozzle should be max. 3 cm above the weeds. Never place the conical or

crevice nozzle directly on the ﬂoor, this could lead to a build-up of heat and damage to the device!

NOTES & TIPS:

• The thicker the root, the longer you should hold the device over the plant in order to achieve the lasting eﬀect

of permanent weed removal. For weeds with particularly thick and/or deep roots (e.g. dandelions) it may be

necessary to repeat the treatment several times at intervals of 1-2 weeks.

• Overly moist soil or damp roots can reduce the eﬀectiveness of the device. In such a case, repeat the treatment in

drier conditions if necessary. Therefore, never use the device immediately after it has rained, as this could impair

the desired eﬀect.

Cooling down and switching oﬀ the device:

EXTREMELY IMPORTANT! First slide the On/Oﬀ switch to the "I" position for at least 1 minute (capital

letters and bold). Only after this should you set to position "0" to switch oﬀ the device. Now fold in the

guide wheels and the stand (metal bracket on the front underside of the device) and lay down the device so

that the front part of the device rests on the stand.

If you use the device as a hand-held device - i.e. without the handle and wheels - fold out the stand (metal

bracket on the front underside of the device), lay the device on it, and allow the device to cool down. Make

sure that you do not allow hot parts of the device to rest on sensitive surfaces such as wood, as this could

lead to scorch marks.

LIGHTING A GRILL (LEVEL 2) - Grill lighter nozzle (available as an option - information on the package)

1. The grill lighter nozzle is intended for lighting your grill or ﬁreplace. Attach the grill lighter nozzle as

described under "Exchanging the attachment".

2. Slide the On/Oﬀ switch to the 2nd position. Allow the device to heat up for approx. 45 seconds.

3. Place the nozzle under the coal or wood. Make sure that the plastic casing of the device is not exposed

to direct heat!

4. Remove the device from the coals or wood as soon as they start to glow.

5. Now direct the nozzle at the coals or wood from a distance of approx. 10-20 cm, until the coal or wood

has reached the desired temperature.

6. This will prevent the nozzle from being exposed to excessive temperatures in the coals, and being

damaged. It also prevents the casing from deforming as a result of the temperature.

7. Turn oﬀ the device before removing it from ﬁre.

RISK OF JAMMING DUE TO OVERHEATING - Only ever use the optionally

available grill lighter nozzle for brieﬂy lighting an outdoor grill or ﬁreplace.

This nozzle is not suitable for removing weeds in narrow spaces (e.g.

crevices). There is a risk of heat build-up as a result of prolonged use,

which can lead to damage to the device!

SWITCHING OFF THE DEVICE: Slide the on/oﬀ switch to position 0.

COOLING & SAFE STORAGE

Before the device is completely switched oﬀ, it must be cooled down. Slide the on/oﬀ switch to position „I“

for at least one minute. After this, the device can be switched oﬀ. The device can be placed on the stand

while it cools down. Never leave the device unattended.

Make sure that the device has cooled down completely before storage.

CLEANING AND CARE

WARNING! Before carrying out any cleaning work, remove the plug from the mains, and ensure

that the device has cooled down completely.

Keep the safety devices, ventilation openings and the motor housing free of dust and dirt. Wipe the device

with a clean cloth, or blow it clean with low-pressure compressed air. We recommend cleaning the device

after each use.

Clean the device regularly with a damp cloth and some mild detergent. Do not use aggressive cleaning

agents or solvents - these can damage the plastic parts of the device. Make sure that no water enters the

device.

M24737_M24977_HammersmithBionicBurner_Manual_20220225_BS.indd 6M24737_M24977_HammersmithBionicBurner_Manual_20220225_BS.indd 6 25.02.22 08:2925.02.22 08:29

HammerSmith M24977 BionicBurner Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info