Bedienungsanleitung Hammond B-3 mk2 (Seite 115 von 130) (Englisch)

495083

115

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

115

Frequently Asked Questions

 Malfunction of the buttons, the keys, etc.

 Turn off the POWER switch once, then turn it on again. If this procedure is not successful, turn off the

POWER switch. While pressing the [RECORD] button, turn the POWER switch on again. (Note that in this

case, all parameters return to their factory-preset status.)

 No sound is produced when the keys are pressed.

 The MASTER VOLUME is at the minimum setting.D

Adjust the volume with the MASTER VOLUME control. (P. 22 #25)

 No Preset key is selected. D

Select a Preset key.

 A plug is inserted to the HEADPHONE jack. D

While a plug is inserted here, the Leslie speaker is disabled.

 The Foot Switch does not work.

 The Foot Switch settings are not correct.D

Reset the Foot Switch correctly in the CONTROL mode. (P. 91 #4)

 The sound does not come out immediately after switched on.

 A Vacuum Tube circuit is mounted in this organ. It takes approximately 10 to 20 seconds after switched on

before you will hear the sound.

 The sound is not distorted if the OVERDRIVE knob is turned.

 When the Overdrive Expression is at “EX-OD”, it does not distort if the Expression pedal is low. In such a

case, increase the Expression pedal, or set the Overdrive Expression at “OD-EX” if you want to distort

regardless of the Expression value. (P. 80 #1)

 Leslie speaker sound is distorted.

 If the sound is distorted regardless of the position of the volume of the Leslie speaker when you are using a

Leslie adapter (such as the 11 pin/6 pin converter), the power of this organ seems to be so large that the sound

is distorted inside the Leslie adapter. In such a case, return the [MASTER VOLUME] knob to 10 o’clock

position.

 The rotor of the external Leslie speaker does not stop, if the Leslie mode is switched

to [STOP].

 Some Leslie Speaker models do not [STOP]. [STOP] is possible on 2101/2102, 122XB, 971 and 3300 (cur-

rent models).

 Audio is interrupted when a Combination Preset is selected.

 Between the Combination Presets with different Tonewheel Settings, the sound will be cut off while the

Tonewheel Settings are switched.

 The sound is once cut between the presets with different key mode (MONO/POLY) on the Pedal part, for

switching the sound algorithm.

 There is excessive MIDI latency compared to the organ (Drawbar) sound.

 The position of the key contact for MIDI send is deeper than that of the multi-contacts for Drawbars.

 There are too many zones to send. D

Turn [OFF] the switches of unnecessary external zones.

 No sounds of Pedal part from the headphones.

 PEDAL OUTPUT set at “PEDOUT”. D

Set the PEDAL OUTPUT at “BOTH” when using the headphones (P. 96 #1).

 Manual contact does not work well.

 The multi-contacts used for the manuals on this organ is designed to be used for a long time. Refer for the

contact refreshing procedures to the “Instruction for keyboard contact cleaning function”.

And, if all the contact points have been worn out and the problem is not solved any longer by refreshing the

contacts, please consult your local dealer or store for further maintenance.

TROUBLESHOOTING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hammond B-3 mk2 Seite 115

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info