Bedienungsanleitung Hammond XM-2 (Seite 51 von 90) (Englisch)

495079

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

Setting The Parameters

8. FOLD-BACK - HIGH

This allows you to set which key the 1' Drawbar starts to FOLD-BACK (= repeat the

same octave) in the upper-most range. The set range is 4G - 5C.

NOTE: The FOLD-BACK can be set not only on the 1' but also 1 1/3', 1 3/5', 2' and 2 2/3'

Drawbars.

Setting the PEDAL

9. TONE-WHEELS

This allows you to select the Tone-wheel waveform of the PEDAL part.

Normal: The traditional B-3/C-3 Tone-wheel sound

Muted: Analog sound represented by the X-5.

Synth1: Sawtooth waveform with swept filter.

Synth2: Dull square waveform.

10. ATTACK

This allows you to set the Attack Rate and the Key-Click Volume at ATTACK and RE-

LEASE.

MAX CLK: Immediately attacks and the key-click is loud.

NORM CLK: Immediately attacks and the key-click is normal.

SOFT CLK: Immediately attacks and the key-click is soft.

NO CLK: A slightly slower attacks without key-click

SLOW ATK: Slow attack without key-click

11. DECAY RATE

This allows you to determine whether to keep voicing or to decay, or set the decay time,

while holding down the key.

The setting range is 1 - 5 and C. The longer the value gets, the longer is the decay time.

No decay at C.

12. SUSTAIN - ON

This allows you to set whether or not to use the Sustain function.

13. SUSTAIN - LENGTH

This allows you to set the Release Rate (= the decay time after you release the key),

when the SUSTAIN - ON (item #12) is ON.

1 is the shortest. And 5 is the longest.

14. VELOCITY

This allows you to set the response to the Velocity. The setting range is OF and 1 - 4. At

OF, the volume does not change however hard you may touch the key. As the value

increases from 1 - 4, the sound gets louder even if you touch the key softly.

15. KEY MODE

This allows you to set the Pedal polyphony.

POLY: Makes it possible to play chords (up to 3 notes)

MONO: Only the lowest note will sound, when you play a chord.

NOTE: The previously released note will be cut when you touch the new one, even when

the PEDAL is in the POLY mode and SUSTAIN is ON.

NOTE: When the note-data of the Pedal are received from the MIDI IN terminal while the

value of the parameter [MIDI IN] (P. 68 #2-4) is “CH”, the Pedal produces polyphonic

sound, regardless of the value.

NOTE: All the parameters in these modes are Patch Parameters. They are recorded into

the Patch.

SUSTAIN

This is the function that the volume slowly fades out

after the key is released, not like that of the synthesiz-

ers.

VELOCITY

“Velocity” is the speed of the key is depressed.

When you touch the piano hard, the hammer hits the

string hard and so the sound is loud.

The organ key is, on the other hand, generally only the

switch to open the valve, and so the sound does not

change however hard you may touch the key.

So this function is effective if you use it when the De-

cay Rate is other than C, or Decay.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hammond XM-2 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info