Bedienungsanleitung Harley-Davidson J03893 (Seite 2 von 2) (Englisch)

640739

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

NOTE

If another accessory is already using the accessory circuit

connector [4], use a Switched Circuit Adapter Harness (Part

No. 70264-94A, available separately) as a "Y" adapter.

6. Mate the heated seat connector to the accessory circuit

connector [4].

7. Follow the instructions in the Owner's Manual to re-connect

the negative (-) battery cable.

8. Guide the wiring into the space beneath the seat so that

the wiring will not be crimped when the seat is installed.

9. Follow the instructions in the Owner's Manual to install the

seat.

After installing seat, pull upward on seat to be sure it is

locked in position. While riding, a loose seat can shift

causing loss of control, which could result in death or

serious injury. (00070b)

10. For 1997 through 2005 FLHT/I/C/CI/CUI models: Pro-

ceed to the OPERATION section.

For 2006 and later FLHT/I/C/CI/CUI, and ALL FLTR

models:

a. See Figure 2. Obtain the new passenger grab strap

(1) from the kit, and the saddlebag front mounting

brackets (4), bolts (3) and flat washers (2) removed

earlier.

b. Install the saddlebag front mounting brackets and

grab strap as shown to the chrome frame tube covers.

Finger-tighten the bolts.

c. Follow the instructions in the Owner's Manual to re-

install the left-side and right-side saddlebags.

d. Tighten the mounting bolts to 60-96 in-lbs (7-11 Nm)

after seating the saddlebags.

is01041

1. Passenger grab strap

2. Original equipment flat washer

3. Original equipment hex head bolt

4. Forward saddlebag mounting bracket

Figure 2. Grab Strap and Saddlebag Front Mounting

Bracket

OPERATION

NOTE

The accessory switch is a rocker switch found on the inner

fairing switch panel.

1. With the ignition/key switch at IGNITION or ACCESS,

open the circuit to the heated seat by flipping the

accessory switch from OFF to ON.

2. Two switches on the side of the seat control the rider and

passenger heating areas independently. The forward

switch controls the rider area, and the rearward switch

controls the passenger area.

a. In the center position, the heat to that area of the seat

is OFF.

b. Pressing the lower part of the switch in toward the

seat turns the heat in that area ON at the LOW set-

ting.

c. Pressing the upper part of the switch in toward the

seat turns the heat in that area ON at the HIGH set-

ting.

NOTES

If the accessory switch is left ON and a seat heater rocker

switch is left in either the LOW or HIGH position when the

motorcycle is turned off, the seat will begin heating when the

ignition/ key switch is turned to the IGNITION or ACCESS

position.

A seat heater in operation while the motorcycle engine is

turned off or running below normal operating speed can

quickly discharge the vehicle battery, which could lead to

a subsequent failure to start, and could damage the elec-

trical system.

is01042

1. Rider section heat control switch

2. Passenger section heat control switch

3. Low heat position

4. High heat position

Figure 3. Seat Heating Control Switches

-J03893 2 of 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harley-Davidson J03893 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info