Bedienungsanleitung Harman Kardon AVR 1510 (Seite 29 von 47) (Englisch)

534559

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

ENGLISH

AVR

System Settings

The AVR’s System Settings menu lets you customize in what way many of the AVR’s

features operate. Press the OSD/Menu button and navigate to the System line. Press the

OK button to display the System Settings menu.

Panel Timeout: This setting allows you to set the AVR’s front-panel display to automatically

turn off after remaining on for a predertimined time (3 – 10 seconds) each time you use

a control. Set this to “Off” to have the display remain on continually.

Auto Power Off: This setting allows you to set the AVR to automatically switch to the Off

mode after being in the Sleep mode for a predetermined time (1 – 8 hours) and switch

to the Sleep mode after this amount of time if a source with an analog audio input or

internal source (FM, AM, USB, iPod, Home Network, vTuner or DMR) is active. See Power

Indicator/Power Button, on page 5, for more information.

Menu Timeout: This setting allows you to set the amount of time (20 – 50 seconds) a

menu screen will remain on after the last adjustment. Set this to “Off” to have the menus

remain on continually until you press the OSD/Menu button.

Status Message: When the AVR is turned on, the volume is adjusted, the source is

changed or a change in the input signal is detected, a status message will be displayed

on the TV screen. Select how long the message remains visible, from 2 to 10 seconds,

with a default of 3 seconds. Select “Off” if you do not wish to see the status messages on

the TV screen (they will still appear on the AVR’s front-panel message display).

Volume Default and Default Volume Setting: These two settings are used together to

program the volume level when you turn on the AVR. Set Volume Default to On, and then

set the Default Volume Setting to the desired turn-on volume. When Volume Default is

set to Off, the AVR will turn on at the last-used volume setting from the previous listening

session.

HDMI Audio to TV: This setting determines whether HDMI audio signals are passed

through the HDMI Monitor Out connector to the video display. In normal operation, leave

this setting at Off, as audio will be played through the AVR. To use the TV by itself, without

the home theater system, turn this setting to On. In this case you will need to mute the

TV’s speakers (or switch the setting to Off) when using the AVR for audio.

HDMI Link: This setting allows the communication of control information among the

HDMI devices in your system. Turn this setting to On to allow control communication

between the HDMI devices; turn the setting to Off to forbid control communication. When

this setting is set to Off, the TV source audio input is set to Optical. When this setting is

set to On, the TV source audio input is set to HDMI ARC.

Software Update: If a software upgrade is released for your AVR, installation instructions

will be available in the Product Support section of the Web site or from Harman Kardon

customer service. At that time, you may use this submenu to install the upgrade

software.

IMPORTANT: During a software upgrade, do not power off the AVR or use any of its

controls. Doing so could permanently damage the AVR.

Sleep Timer

The sleep timer sets the AVR to play for up to 90 minutes and then turn off

automatically.

Press the Sleep button on the remote, and the time until turn-off will be displayed. Each

additional press of the Sleep button decreases the play time by 10 minutes, from 90 to

10 minutes. The SLEEP OFF setting disables the sleep timer.

When the sleep timer has been set, the front-panel display will automatically dim to half

brightness.

If you press the Sleep button after the timer has been set, the remaining play time will be

displayed. Press the Sleep button again to change the play time.

Processor Reset

If the AVR behaves erratically after a power surge, unplug the AC power cord for at least

3 minutes. Plug the cord back in and turn the AVR on. If this procedure doesn’t help, reset

the AVR’s processor as described below.

NOTE:

A processor reset erases all user conﬁgurations, including speaker and level

settings, and tuner presets. After a reset, reenter all of these settings from your entries

in the Appendix worksheets.

To reset the AVR’s processor:

1. Press the front-panel Standby/On switch for more than three seconds to turn the AVR

off (the Power Indicator will turn amber).

2. Press and hold the front-panel Surround Modes button for at least 5 seconds until the

RESET message appears on the front-panel Message Display.

NOTE:

After performing a processor reset, wait at least 1 minute before pressing any

Source Selector buttons.

If the AVR does not function correctly after a processor reset, contact an authorized

Harman Kardon service center for assistance. Authorized service centers may be located

by visiting our Web site at www.harmankardon.com.

System Settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR 1510 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 1510

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info