Bedienungsanleitung Harman Kardon AVR 1565 (Seite 11 von 41) (Englisch)

502783

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

AVR 1565/AVR 1566 Types of Home Theater System Connections

Types of Home Theater System Connections

There are different types of audio and video connections used to connect the AVR to your

speakers, your TV or video display, and your source devices. The Consumer Electronics

Association has established the CEA

color-coding standard.

Connection Color Guide Table

Analog Audio Connection Color

Front Left/Right White/Red

Center Green

Surround Left/Right Blue/Gray

Subwoofer Purple

Digital Audio Connection Color

Coaxial (input or output) Orange

Optical Input Black

Analog Video Connection Color

Component Video Red/Green/Blue

Composite Video Yellow

Speaker Connections

Speaker cables carry an ampliﬁed signal from the AVR’s speaker terminals to each

loudspeaker. Each cable contains two wire conductors, or leads, that are differentiated

in some way, such as with colors or stripes.

The differentiation helps you maintain proper polarity, without which your system’s low-

frequency performance can suffer. Each speaker is connected to the AVR’s speaker-

output terminals using two wires, one positive (+) and one negative (–). Always connect

the positive terminal on the speaker, which is usually colored red, to the positive terminal

on the AVR, which is colored as indicated in the Connection Color Guide Table, above. The

negative terminals on the speakers and the AVR are black.

Your AVR uses binding-post speaker terminals that can accept bare-wire cables or

banana plugs. Bare-wire cables are installed as shown below:

1. Unscrew Cap 3. Tighten Cap2. Insert Bare Wire

Banana plugs are inserted into the hole in the middle of the terminal cap, as shown

below:

A. Tighten Cap B. Insert Banana Connector

into Hole in Cap

Always connect the colored (+) terminal on the AVR to the (+) terminal on the speaker

(usually red), and the black (–) terminal on the AVR to the (–) terminal on the speaker

(usually black).

IMPORTANT: Make sure the ( + ) and ( – ) bare wires do not touch each other or

the other terminal. Touching wires can cause a short circuit that can damage your

AVR or ampliﬁer.

Subwoofer Connections

The subwoofer is a speaker dedicated to reproducing only the low (bass) frequencies,

which require more power. To obtain the best results, most speaker manufacturers offer

powered subwoofers that contain their own ampliﬁers. Use a single RCA audio cable

(not included) to make a line-level (non-ampliﬁed) connection from the AVR’s Subwoofer

connector to a corresponding input jack on the subwoofer.

Although the AVR’s purple subwoofer output looks similar to a full-range analog audio

jack, it is ﬁltered so that only the low frequencies pass through it. Don’t connect this

output to any device other than a subwoofer.

Source Device Connections

Audio and video signals originate in source devices (components where a playback

signal originates) such as your Blu-ray Disc or DVD player, CD player, DVR (digital video

recorder) or other recorder, tape deck, game console, cable or satellite television tuner,

iPod or iPhone (docked in an optional The Bridge IIIP docking station) or MP3 player. The

AVR’s FM/AM tuner also counts as a source, even though no external connectors are

needed other than the AVR’s FM and AM antennas. Separate connectors are required

for the audio and video portions of the source device’s signal, except for digital HDMI

connectors. The types of connectors you use will depend upon the capabilities of the

source device and of your TV or video display.

Digital Audio Connections – HDMI

There are two types of audio connections – digital and analog. Digital audio signals are

required for listening to sources encoded with digital surround modes, such as Dolby

Digital and DTS, or for uncompressed PCM digital audio. Your AVR has three types of

digital audio connectors: HDMI, coaxial and optical. Do not use more than one type of

digital audio connector for each source device. However, it’s okay to make both analog

and digital audio connections to the same source.

Your AVR is equipped with four rear-panel HDMI input connectors and one HDMI monitor

output connector. HDMI technology enables digital audio and video information to be

carried using a single cable, delivering the highest quality picture and sound. If your TV

or video-display device has an HDMI input connector, make a single HDMI connection

from each source device to the AVR. Usually, a separate digital audio connection is not

required.

The AVR’s HDMI Monitor Output connector contains an Audio Return Channel (ARC) that

carries a digital audio signal from your TV or video display back to the AVR. It allows

you to listen to HDMI devices that are connected directly to your TV (such as an Internet

connection) without making an additional connection from the device to the AVR. The

ARC signal is active when the TV source is selected. See System Setup, on page 22, for

more information.

The HDMI connector is shaped for easy plug-in (see illustration, below), and HDMI cable

runs are limited to about 10 feet (3m). If your video display has a DVI input and is

HDCP-compliant, use an HDMI-to-DVI adapter (not included), and make a separate audio

connection.

Digital Audio Connections – Coaxial

Coaxial digital audio jacks are usually color-coded orange. Although they look like

standard RCA-type analog jacks, you should not connect coaxial digital audio outputs to

analog inputs or vice versa.

Harman Kardon AVR 1565 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info