Bedienungsanleitung Harman Kardon AVR 1566 (Seite 19 von 41) (Englisch)

502784

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

AVR 1565/AVR 1566

Set Up the AVR, continued,

and Operating Your AVR

5. For each source device you connected to a digital audio input:

a) Use the remote’s Up and Down arrow buttons to select “Source.” Use the Left

and Right arrow buttons to change the listed source to one of the sources you

connected to a digital audio input connector.

b) Use the remote’s down arrow button to select “Audio In.”

* INPUT SETUP *

SOURCE : DVD

TITLE:

AUDIO IN : OPT 1

AUTO POLL : ON

BXR : OFF

TONE : IN

BASS : 0

TREBLE : 0

BACK TO MASTER MENU

c) Use the remote’s Left and Right arrow buttons to select the digital audio input

where you connected the source device.

Additional Input Setup Menu Items

You can also adjust the following settings independently for each source:

Title: You may change the display name for any source (except the radio). This feature

may help you to select the correct source device even when you have forgotten which

physical connections you used.

1. Move the cursor to the Title line and press the OK button. A block cursor will blink.

2. Use the Up/Down buttons to scroll through the alphabet in upper and lower case,

the numbers and many punctuation marks. When you have selected the desired

character, press the Right button to move to the next space. Press the Right button

twice to leave a blank space.

3. Press the OK button when you have ﬁnished.

Auto Poll: The Auto Poll feature is used when both an analog audio and a digital audio

connection have been made for one source device. If no digital signal is available, the

AVR will automatically switch to the analog input for the source. This situation can occur

with some cable or satellite television broadcasts, where some channels are broadcast

with digital audio and others with analog audio, or when a DVD player is paused or

stopped.

For some sources such as DVD players, the Auto Poll feature is unnecessary and may be

undesirable. To turn Auto Poll off, move the cursor to the Auto Poll line and press the Left/

Right buttons until Off appears. With Auto Poll turned off, the AVR will check for a signal

only at the audio input assigned to the source.

The remaining Input Setup menu items adjust the AVR’s audio performance for that

source and may be skipped at this time. For most listening, we recommend leaving

these settings at their factory defaults, allowing you to enjoy the sound mix created by

your favorite movie and music artists.

BXR: Enhances bass performance when playing MP3 tracks. Select On, or leave it at the

default Off setting for non-MP3 audio sources.

Tone: This setting determines whether the treble and bass controls are active. When this

line is set to Off, the tone controls are out of the circuit, with no changes to the sound.

When this line is set to On, the bass and treble frequencies are boosted or cut, depending

upon the Bass and Treble settings (see below).

Bass and Treble: Boost or cut the low or high frequencies by up to 10dB by using the

Left/Right buttons to change the setting by 2dB at a time.

When you’re ﬁnished, press the remote’s OSD button to turn off the on-screen menu.

Operating Your AVR

Now that you have installed your components and completed a basic conﬁguration, you

are ready to begin enjoying your home theater system.

Controlling the Volume

Adjust the volume either by turning the front-panel Volume knob (clockwise to increase

volume or counterclockwise to decrease volume) or by pressing the Volume Up/Down

buttons on the remote. The volume is displayed as a negative number of decibels (dB)

below the 0dB reference point.

0dB is the maximum recommended volume for your AVR. Although it’s possible to turn

the volume to a higher level, doing so may damage your hearing and your speakers. For

certain more dynamic audio materials, even 0dB may be too high, allowing for damage

to equipment. Use caution with regard to volume levels.

Muting the Sound

To mute all speakers and the headphones, press the Mute button on the remote. Any

recording in progress will not be affected. The MUTE message will appear in the front-

panel display as a reminder. To restore the sound, press the Mute button again, or adjust

the volume.

Listening Through Headphones

Plug the 1/4-inch stereo plug on a pair of headphones into the front-panel Phones

jack for private listening. The default Headphone Bypass mode delivers a conventional

two-channel signal to the headphones. Press the Surround Modes button on the front

panel or use the remote and OSD to switch to HARMAN headphone virtual surround

processing, which emulates a 5.1-channel speaker system. No other surround modes

are available for the headphones.

Selecting a Source

There are two different ways to select a source:

• Press the front-panel Source Select buttons.

• Directly select any source by pressing its Source Selector button on the remote.

The AVR selects the audio and video inputs assigned to the source and any other

settings you made during setup.

The source name, the audio and video inputs assigned to the source, and the surround

mode will appear on the front panel.

Video Troubleshooting Tips

If there is no picture:

• Check the source selection.

• Check all connections for a loose or incorrect connection.

• Check the video-input selection on the TV/display device.

Additional Tips for Troubleshooting HDMI Connections

• Turn off all devices (including the TV, the AVR and any source components).

• Unplug the HDMI cables, starting with the cable between the AVR and the TV, and

continuing with the cables between the AVR and each source device.

• Carefully reconnect the cables from the source devices to the AVR. Connect the

cable from the AVR to the TV last.

• Turn on the devices in this order: TV, AVR, source devices.

NOTE: Depending upon the particular components involved, the complexity of

the required communication between HDMI components may cause delays of

up to a minute in the completion of some actions, such as input switching or

switching between SD and HD channels.

Harman Kardon AVR 1566 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info