Bedienungsanleitung Harman Kardon AVR 1650 (Seite 5 von 42) (Englisch)

502591

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

AVR 1650/AVR 165

ENGLISH

Front-Panel Controls, continued

Power indicator: This LED has three possible modes:

LED is off: Indicates that the AVR is unplugged or the rear-panel Main Power switch s

is off.

LED glows amber: Indicates that the AVR is in the Standby mode. s

LED glows white: Indicates that the AVR is turned on. s

IMPORTANT NOTE: If the PROTECT message ever appears on the AVR’s front-panel

Message display, turn off the AVR and unplug it from the AC outlet. Check all speaker

wires for a possible short circuit (the “+” and “–” conductors touching each other

or both touching the same piece of metal). If a short circuit is not found, bring the

unit to an authorized Harman Kardon service center for inspection and repair before

using it again.

IR sensor: This sensor receives infrared (IR) commands from the remote control. It is

important to ensure that the sensor is not blocked.

Set button: Press this button to select the currently highlighted menu item.

Message display: Various messages appear in this two-line display in response to

commands and changes in the incoming signal. In normal operation, the current source

name appears on the upper line, while the surround mode is displayed on the lower line.

When the on-screen display menu system (OSD) is in use, the current menu settings

appear.

Surround-Mode Select buttons: After you have selected the desired surround-mode

category, press these buttons to select a speciﬁc mode within the category, such as to

change from Dolby

Pro Logic

II Movie mode to Logic 7

Movie mode. Surround-mode

availability depends on the nature of the source input signal, i.e., digital versus analog,

and the number of channels encoded within the signal.

Volume knob: Turn this knob to raise or lower the volume.

Power button: Press this button to turn the AVR on or to place it in the Standby mode.

Tuning Mode button: This button toggles between manual (one frequency step at a

time) and automatic (seeks frequencies with acceptable signal strength) tuning mode. It

also toggles between stereo and mono modes when an FM station is tuned in.

Channel Level Control button: Press this button to activate the channel-level adjustment

feature. After pressing this button, use the Up/Down buttons to select the channel for

adjustment and use the Left/Right buttons to adjust the channel’s level.

Digital Input button: Press this button to change the audio input for the current source.

Use the Left/Right buttons to cycle through the available inputs. Although you can

assign any digital audio input to any source, the analog audio inputs are all permanently

dedicated to the source with which they are labeled.

Left/Right buttons: Use these buttons to navigate the AVR’s menus.

Up/Down buttons/Tuning buttons: Use these buttons to navigate the AVR’s menus.

When the radio is the active source, use these buttons to tune stations according to the

setting of the Tuning Mode button (see above).

Surround-Mode Category button: Press this button to select a surround-sound

category. Each press changes the surround-mode category: Auto Select, Virtual, Stereo,

Movie, Music and Video Game. To change the speciﬁc surround-sound mode within the

category, use the Surround Mode Select buttons. See

Audio Processing and Surround

Sound,

on page 20, for more information on surround modes.

Headphone jack/EzSet/EQ Mic connector: Connect a 1/4" stereo headphone plug to

this jack for private listening. This jack is also used to connect the supplied microphone

for the EzSet/EQ procedure described in

Conﬁgure the AVR for Your Speakers,

page 17.

Source Select buttons: Press these buttons to select the active source.

USB port: You can use this port to perform software upgrades that may be offered in

the future. Do not connect a storage device, a peripheral product or a PC here, unless

instructed to do so as part of an upgrade procedure.

Aux Analog Audio Input connector: Connect an auxiliary source component that will

be used only temporarily, such as a camcorder, portable music player or game console,

here.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR 1650 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 1650

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info