Bedienungsanleitung Harman Kardon AVR 1710 (Seite 21 von 52) (Englisch)

534553

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ENGLISH

AVR

Set Up the Remote Control

Install the Batteries in the Remote Control

Remove the remote control’s battery cover, insert the two supplied AAA batteries as

shown in the illustration, and replace the battery cover.

1. Remove

Cover

2. Insert

Batteries

3. Replace

Cover

Program the Remote to Control Your Source Devices and TV

You can program your AVR remote to control many brands and models of audio/video

source devices and TVs. The remote is also ready to operate your iPod or iPhone when it

is connected to the AVR’s front-panel USB port.

Each of the remote’s Source Selector buttons has been preprogrammed to control certain

types of source devices:

Cable/Sat: Controls cable TV and satellite TV tuner boxes

Disc: Controls Blu-ray Disc and DVD players

Radio:

Controls the AVR’s built-in FM/AM tuner

TV:

Controls TVs and video displays

USB:

Browses compatible media on an Apple iOS device that is connected to, or a USB

device that is inserted in the AVR’s USB port Note: Does not require programming.

DVR:

Controls TiVo

recorders

Game:

Controls video-game consoles

Media Server:

Controls media servers

Network:

Browses compatible media on DLNA-compatible devices connected to your

home network and on vTuner (Internet Radio). Note: Does not require programming.

AUX:

Controls HDTV tuner boxes, CD players, VCRs and PVDs.

Although the Source Selector buttons are preprogrammed for the device types listed

above, you can reassign a Source Selector button to a different device type. See

Reassigning a Source Selector Button for a Different Device Type, on page 21.

Once you have programmed the remote, you can switch the remote’s control mode to

access the functions for a particular device by pressing the remote’s Source Selector

button for that device.

Follow these steps to program the Source Selector buttons for your source devices:

1. Turn on the source device you want to program the remote to control.

2. Look up the code numbers for the device in Tables A12-A22 in the Appendix. Write all

the applicable code numbers in a convenient place.

3. Press the Source Selector button for the device and hold it as it glows red, goes dark

and glows red again. Then release it. The remote is now in the Programming mode.

NOTE:

The remote will remain in the Programming mode for 20 seconds. If you do not

complete Step 4 within 20 seconds, the remote will exit the Programming mode, and you

will need to repeat Step 3.

4. Aim the remote at the source device and use the remote’s Number buttons to enter a

code number from Step 1, above.

a) If the device turns off, press the Source Selector button again to save the code. The

Source Selector button will ﬂash, and the remote will exit the Programming mode.

b) If the device does not turn off, enter another code number.

c) If you run out of code numbers for a device, you can search through all of the codes

in the remote’s library for dervices of its type by pressing the remote’s Up button

repeatedly until the device turns off. When it does, press the Source Selector button

to save the code.

5. Check that other functions control the device correctly. Sometimes manufacturers use

the same Power code for several models, while other function codes vary. Repeat this

process until you’ve programmed a satisfactory code set that operates most of the

device’s functions.

6. If you searched through the remote’s code library to ﬁnd the code, you can ﬁnd out

which code number you have programmed by pressing and holding the Source Selector

button to re-enter the Programming Mode. Then press the remote’s OK Button, and the

Source Selector button will ﬂash in the code sequence. One ﬂash represents “1,” two

ﬂashes for “2,” and so forth. A series of quick ﬂashes represents “0.” Record the code

number programmed for each device in Table A7 in the Appendix.

Repeat Steps 3 – 6 for each source device you want to control with the AVR remote.

Reassigning a Source Selector Button for a Different Device Type

You can reassign a Source Button to control a different device type (for example, you can

program the Media Server button to control a DVD player).

1. Turn on the source device you want the remote to control.

2. Look up the code numbers for the device in Tables A12-A22 in the Appendix. Write all

the applicable code numbers in a convenient place.

3. Press the Source Selector button you want to override and hold it for three seconds

as it glows red, goes dark and glows red again. Then release it. The remote is now in

the Programming mode.

4. Press the Source Selector button that corresponds to the source device’s type (i.e.,

for a DVD player, press the Blu-ray button). The Source Selector button you pressed in

Step 3 will ﬂash once.

5. Aim the remote at the source device and use the remote’s Number buttons to enter a

code number from Step 2, above.

a) If the device turns off, press the Source Selector button from Step 3 again to

save the code. The Source Selector button will ﬂash, and the remote will exit the

Programming mode.

b) If the device does not turn off, enter another code number.

c) If you run out of code numbers for a device, you can search through all of the codes

in the remote’s library for devices of its type by pressing the remote’s Up button

repeatedly until the device turns off. When it does, press the Source Selector button

from Step 3 to save the code.

Most of the button labels on the AVR remote describe each button’s function when the

remote is used to control the AVR. However, the button may perform a different function

when used to control another device. Refer to the Remote Control Function List, Table

A13 in the Appendix.

Harman Kardon AVR 1710 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 1710

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info