Bedienungsanleitung Harman Kardon AVR 171S (Seite 23 von 52) (Englisch)

599836

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

AVR

ENGLISH

7. Select “Auto: EzSet/EQ”.

8. If you have a subwoofer connected, select “Yes with Sub.” Otherwise, select “Yes

without Sub.”

9. For AVR 1610S/AVR 161S, or for AVR 1710S/AVR 171S’s in 5.0- or 5.1-channel

systems, select “5.0” or “5.1” in the Speaker Conﬁguration screen. For AVR 1710S/

AVR 171S’s in 7.0- or 7.1-channel systems, select “7.0” or “7.1.”

10. The test will begin. Make sure that the room is quiet while the test noise is playing

through the speakers.

11. When the test ﬁnishes, select “Done” to exit.

NOTES:

• If there are fewer than ﬁve main speakers in your system, do not use the EzSet/

EQ process. Instead, proceed as described in Manual Speaker Setup, on page 30.

• If you are using an AVR 1710S/AVR 171S in 6.0- or 6.1-channel conﬁguration with a

single surround back speaker, do not use the EzSet/EQ process. Instead, proceed as

described in Manual Speaker Setup, on page 30.

Set Up Your Sources

The Source Setup menu lets you assign the correct physical audio and video connections

to each source and lets you set many audio and video playback features for each source.

IMPORTANT: The “Video In” and “Audio In” settings are not optional and must

be adjusted before you use your AVR to enable playback of each source. You can

adjust the other settings later. See System Settings, on page 34, for complete information

about adjusting all of the Settings menu options.

1. Review the input connections you listed on the Source Buttons and Assigned

Connectors table, on page 16. Note what changes (if any) you want to make from the

default connector assignments that appear on the list.

2. Turn on your TV and select the TV input where you connected the AVR in Connect Your

TV or Video Display, on page 15.

3. Press the remote control’s OSD/Menu button. The AVR’s OSD setup menu will appear

on the TV. (Note: If you have used a composite video connection to your TV, the OSD

menus will not appear on your TV. Follow the steps below using the AVR’s front-panel

display.)

4. Use the remote’s arrow and OK buttons to select “Source Setup,” and use the left/right

arrow buttons to select a source button with connectors that you want to re-assign.

5. Select “Video In” and select the video input connector you want to assign to the source

button. Press the OK button. NOTE: If you select an HDMI connector as the video input

connector, the audio input connector will automatically change to the same HDMI

connector.

6. If you have not selected an HDMI connector for Video In, select “Audio In” and select

the audio input connector you want to assign to the source button. Press the OK button.

You cannot use a different video input connector with an HDMI audio input connector.

7. Press the remote’s Back/Exit button and repeat steps 3 – 6 for the remaining source

buttons with connectors you want to re-assign.

Title: This selection lets you change the display name for the source, which is useful if

your source’s device type is different from the source’s preprogrammed name. Use the

Up/Down buttons to scroll forward or backward through the alphanumeric characters

until the desired character appears, then use the Left/Right buttons to move the cursor to

the next or previous position. Move the cursor again to leave a blank space. (Your name

can have a maximum of 10 characters.) When you have ﬁnished, press the OK Button.

The new name will appear on the AVR’s front panel and throughout the on-screen menu

system.

Tone: This setting determines whether the treble and bass controls are active for the

source. When it’s set to Off, the tone controls are out of the circuit, with no changes to the

sound. When it’s set to On, the bass and treble controls are in the circuit.

Treble/Bass: These settings boost or cut the treble or bass frequencies by up to 10dB,

in 2dB increments. Use the Left/Right buttons to change the setting. The default setting

is 0dB.

Night Mode: This setting activates Night mode for the source, which works with specially

encoded Dolby Digital discs or broadcasts. Night mode compresses the audio so that

louder passages are reduced in volume to avoid disturbing others, while dialogue

remains intelligible. The following settings are available:

• Off: No compression is applied. Loud passages in the program remain as they were

recorded.

• Mid: Loud passages in the program are reduced moderately in volume. Dolby True

HD stream is compressed automatically as set by the incoming stream.

• Max: Loud passages in the program are reduced more in volume.

Set Up the AVR

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR 171S Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 171S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info