Bedienungsanleitung Harman Kardon AVR 265 (Seite 7 von 62) (Englisch)

502603

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

AVR

ENGLISH

Rear-Panel Connectors, continued

Composite Video Monitor Out connector: If your TV or video display does not

have an HDMI connector, use a composite video cable (not included) to connect the

AVR’s Composite Video Monitor Out connector to your TV’s composite video input.

NOTE: The HDMI connection to your TV is preferred. If you use the composite video

connection to your TV, you will not be able to view the AVR’s on-screen menus.

Composite Video Record Out connector: Connect an analog video recorder’s video

input connector to the AVR’s Composite Video Rec Out connector. You can record

any composite video input signal. NOTE: To record the audio and video from the

source device, connect the AVR’s Analog Record Output connectors to the analog

video recorder’s audio inputs.

Component Video Input connectors: If any of your video source devices have

component video connectors (and do not have HDMI connectors), using the

component video connectors will provide superior video performance. You will also

need to make an audio connection from the device to the receiver. See

Connect Your

Audio and Video Source Devices

, on page 18, for more information.

SIRIUS

Tuner connector: Connect a SIRIUSConnect

™

satellite radio tuner module

here. (Not included. Available at www.sirius.com.) See

Connect Your Audio and Video

Source Devices

, on page 18, for more information.

12V Trigger connector: This connector provides 12V DC whenever the AVR is on.

It can be used to turn on and off other devices such as a powered subwoofer.

Zone 2 IR Input connector (AVR 3650/AVR 365 only): Connect a remote IR receiver

located in Zone 2 of a multizone system to this jack to control the AVR (and any

source devices connected to the Remote IR Output connector) from the remote

zone.

The Bridge IIIP connector: Connect an optional Harman Kardon The Bridge IIIP

docking station to this input. Insert the plug until it snaps into place in the connector.

IMPORTANT: Connect The Bridge IIIP only with the AVR’s power turned off.

Radio Antenna connectors: Connect the included AM and FM antennas to their

respective terminals for radio reception.

Zone 2 Out connectors: Connect these jacks to an external ampliﬁer to power the

speakers in the remote zone of a multizone system.

Subwoofer connector: Connect this jack to a powered subwoofer with a line-level

input. See

Connect Your Subwoofer

, on page 17, for more information.

Analog Audio Input connectors: Use the AVR’s Analog Audio Input connectors for

source devices that don’t have HDMI or digital audio connectors. See

Connect Your

Audio and Video Source Devices

, on page 18, for more information.

Optical Digital Output connector: Connect a digital audio recorder’s optical digital

input to the AVR’s Optical Digital Output connector. You can record both coaxial and

optical digital audio signals.

Speaker connectors: Use two-conductor speaker wire to connect each set of

terminals to the correct speaker. See

Connect Your Speakers

, on page 17, for more

information.

NOTE: The speaker connectors, also called Assigned Amp speaker connectors-

are used for the surround back channels in a 7.1- channel home theater, or you

can reassign them to a remote room for multizone operation or to front height

channels for Dolby Pro Logic

IIz operation. See

Place Your Speakers

, on page

13, for more information.

Network connector: Use a Cat. 5 or Cat. 5E cable (not supplied) to connect the AVR’s

Network connector to your home network to enjoy Internet radio and content from

DLNA

-compatible devices that are connected to the network. See

Connect to Your

Home Network

, on page 20, for more information.

Main Power switch: This mechanical switch turns the AVR’s power supply on or off.

It is usually left on, and it cannot be turned on or off using the remote control.

AC Input connector: After you have made all other connections, plug the supplied

AC power cord into this receptacle and into an unswitched wall outlet.

RS-232 connector: This connector is used to connect to external control hardware.

Consult a certiﬁed professional installer for more information.

IR Remote In/Out connectors (AVR 3650/AVR 365 only): When the IR sensor

on the front panel is blocked (such as when the AVR is installed inside a cabinet),

connect an optional IR receiver to the IR Remote In jack. The IR Remote Out jack

may be connected to the IR input of a compatible product to enable remote control

through the AVR.

Fan Vents: These vents are used by the AVR’s fan to cool the system. Maintain

a clearance of at least three inches (75mm) from the nearest surface to avoid

overheating the unit. It is normal for the fan to remain off at most normal volume

levels. An automatic temperature sensor turns the fan on only when it is needed.

IMPORTANT NOTE: Never block the fan vents. Doing so could allow the AVR to

overheat to dangerous levels.

0295CSK - HK (x65Series) AVR3650_365_2650_265 CORE OM, WORK18 danny.indd 7 01/07/11 11:33:30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR 265 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 265

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info