Bedienungsanleitung Harman Kardon AVR 347 (Seite 10 von 76) (Englisch)

502541

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

REAR-PANEL CONNECTIONS

AM and FM Antenna Terminals: Connect the included AM and

FM antennas to their respective terminals for radio reception.

XM Antenna Jack: Plug in an XM antenna module here. The XM

antenna module is purchased separately, and should specify that it is

for home use with an XM Ready

product. You will need to subscribe to

the XM service, which is available separately, and activate the service for

your antenna module. (XM service is not available in Alaska and Hawaii.)

Front, Center and Surround Speaker Outputs: Use two-

conductor speaker wire to connect each set of terminals to the correct

speaker. Remember to observe the correct polarity (positive and

negative connections). Always connect the positive lead to the colored

terminal on the receiver and the red terminal on the speaker. Connect

the negative lead to the black terminal on both the receiver and the

speaker. See the Connections section for more information on connect-

ing your speakers.

Surround Back/Multiroom Speaker Outputs: These speaker

outputs may be used either for the surround back channels in a 7.l-

channel home theater, or they may be reassigned to a remote room for

use with a multiroom system. When these outputs are reassigned for

multiroom operation, only a 5.1-channel configuration will be available in

the main listening room. Use the on-screen menu system to configure

these channels as desired.

As with the other speaker outputs, remember to observe proper polarity

by connecting the positive and negative output terminals to the corre-

sponding terminals on each speaker.

Subwoofer Output: If you have a powered subwoofer with a line-

level input, connect it to this jack.

Preamp Outputs: Connect these jacks to an external amplifier if

more power is desired.

Surround Back/Multiroom Preamp Outputs: These outputs

may be used with an external amplifier either to power the surround

back channels, or to power the speakers in the remote zone of a multi-

channel system. Use the on-screen menu system to configure these

channels as desired.

Remote Infrared (IR) Input and Output: When the remote IR

receiver on the front panel is blocked, such as when the AVR is placed

inside a cabinet, connect an optional IR receiver to the Remote IR Input

jack for use with the remote control. The Remote IR Output may be

connected to the Remote IR Input of a compatible source device (or

other product) to enable remote control through the AVR. This is particu-

larly useful in multiroom applications, when you wish to control the

source device from the remote room (when used with the Multiroom IR

Input). When several source devices are used, connect them in “daisy

chain” fashion.

Multiroom Infrared (IR) Input: Connect a remote IR receiver

located in the remote zone of a multiroom system to this jack to control

the AVR and any source devices connected to the Remote IR Output

from the remote zone.

Remote IR Carrier Output: This output is similar in function to

the Remote IR Output, with the difference that this jack outputs the

full infrared signal as received by the AVR’s IR sensor or the Remote

IR Input, while the Remote IR Output jack outputs a “stripped” signal

that has no carrier frequency. The full signal may be required by some

components with IR inputs. It may also be required when you connect

external IR emitters or other devices to the AVR to pass IR signals to

other components.

Multiroom Audio Outputs: Connect these jacks to an external

amplifier to power the speakers in the remote zone of a multiroom

system. When these jacks are used, it is possible to have a full 7.1-

channel system in the main listening room at the same time the

multiroom system is in use.

A-BUS Port: Use a Category 5/5e cable to connect this port to

optional A-BUS equipment for multiroom operation. When the A-BUS

system is used, it is possible to have a full 7.1-channel system in the

main listening room at the same time the multiroom system is in use.

Video 1, Video 2, Video 3 and DVD Audio/Video Inputs:

These jacks may be used to connect your video-capable source

components (e.g., VCR, DVD player, cable TV box) to the receiver.

Remember to use only one type of video connection for each source.

See the Connections section for more information on audio and video

connection options for each source component.

Video 1 Audio/Video Outputs: These jacks may be used to

connect your VCR or another recorder.

Composite and S-Video Monitor Outputs: If any of your

sources use composite or S-video connections, you may need to

connect one or both of these monitor outputs to the corresponding

inputs on your television or video display in order to view the sources

and to view the on-screen displays. If your video display is equipped

with component video or HDMI inputs, you may take advantage of the

AVR 347’s transcoding capability, which transcodes composite and

S-video signals to component video and HDMI, allowing for only a

single video connection from the AVR to the video display.

HDMI Inputs and Output: HDMI (High-Definition Multimedia

Interface) is a newer type of connection for transmitting digital audio and

video signals between devices. With the AVR 347’s powerful processor,

you may connect up to two HDMI-equipped source devices to the HDMI

inputs using a single-cable connection, while benefiting from superior

digital audio and video performance. However, if your video display is

not HDMI-compatible, you will need to connect the device to one of the

other source inputs, selecting a coaxial or optical digital audio input and

analog video input. See the Connections and Installation sections for

more information.

If your video display has an HDMI input, but some of your sources have

only analog video outputs, you may still rely on just the HDMI video

connection to your display; the AVR 347 will automatically transcode

analog video signals up to 720p to the HDMI format. High-resolution

analog 1080i or higher signals are not available at the HDMI Output,

but 1080i signals received through one of the HDMI Inputs will be

passed through directly to the HDMI Output without any video processing.

AVR347 om.qxd 7/10/07 11:00 AM Page 10

Harman Kardon AVR 347 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 347

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info