Bedienungsanleitung Harman Kardon AVR 347 (Seite 24 von 76) (Englisch)

502541

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INSTALLATION

You are now ready to connect your various components to your receiver.

Before beginning, make sure that all components, including the AVR 347,

are turned completely off and their power cords are unplugged. Don’t

plug any of the power cords back in until you have finished

making all of your connections.

Remember that your receiver generates heat while it is on. Select

a location that leaves several inches of space on all sides of the receiver.

It is preferable to avoid completely enclosing the receiver inside a

cabinet. It is also preferable to place components on separate shelves

rather than stacking them directly on top of the receiver. Some surface

finishes are delicate. Try to select a location with a sturdy surface finish.

Step One – Connect the Speakers

If you have not yet done so, place your speakers in the listening room,

as described in the Speaker Placement section above.

Connect the center, front left, front right, surround left, surround

right, surround back left and surround back right loudspeakers to the

corresponding speaker terminals on the AVR 347. See Figure 17.

Remember to maintain the proper polarity by always connecting the

positive and negative terminals on each speaker to the positive and

negative terminals on the receiver. Use the Connection Color Guide

on page 19 as a reference.

Figure 17 – Speaker Connections

NOTE: If you only have one surround back speaker, wait until

after you have run EzSet/EQ in the Initial Setup section before

connecting it to the Surround Back Left speaker outputs.

Step Two – Connect the Subwoofer

Connect the Subwoofer Output on the AVR 347 to the line-level input on

your subwoofer. See Figure 18. Consult the manufacturer’s guide for the

subwoofer for additional information.

Figure 18 – Subwoofer Connection

Step Three – Connect the Antennas

Connect the FM and AM antennas to their terminals. If you have purchased

an XM antenna module designed for connection to an XM Ready device,

such as the AVR 347, you may connect it now. To enjoy XM Radio,

remember to purchase a subscription and activate your antenna module.

More information is available at www.xmradio.com.See Figure 19.

Figure 19 – Antenna Connections

Step Four – Connect the Source Components

Use the Table A4 worksheet in the Appendix to note which connections

you will use for each of your source devices.

For each source, select a source input (Video 1, Video 2, Video 3, etc.).

In Table 2 we recommend connecting certain types of sources to certain

source inputs to make it easier to program and use the remote control.

Decide which audio connections you will use. If your source device has

them, use

one of

the HDMI, coaxial digital or the optical digital audio

connection. Referring to Table 2, we recommend that you connect the

DVD source to the Coaxial 1 input jack, and the source designated

Video 2 to the Optical 1 input jack. If you are using the HDMI inputs,

then in most cases no other audio connection is required. If your source

outputs video but not audio via its HDMI connection, then select any

available digital audio input on the AVR to use with the source. If your

HDMI source plays DVD-Audio, SACD, HD-DVD, Blu-ray Discs or another

multichannel audio format, connect its multichannel analog audio outputs

to the AVR 347’s 6-/8-Channel Inputs, and connect one of its analog

video outputs to a source input on the AVR 347 (e.g., Component Video

3 or Video 3). When you select that source input, e.g., Video 3, select

the 6-/8-Channel Inputs, and the AVR will automatically use the analog

video input.

NOTE: The multichannel analog audio connection is not required

for DVD-Audio players compliant with HDMI version 1.1 or better,

or HD-DVD and Blu-ray Disc players that decode the digital audio

internally and output linear PCM signals in digital format. Consult

the owner’s guide for your disc player for more information.

In addition to the digital audio connections, we recommend that you

connect the analog audio connections for each source, as a backup to

the digital connections, for recording, for use with the multiroom system,

or in the event that you use all eight of the digital audio inputs for other

devices. For sources that don’t have digital audio outputs, you must use

the analog audio connections.

AVR 347

SUB

AVR 347

FR FL

SBR

SBL

AVR347 om.qxd 7/10/07 11:01 AM Page 24

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR 347 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 347

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info