Bedienungsanleitung Harman Kardon AVR 4000 (Seite 15 von 58) (Englisch)

8518

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

INSTALLATION AND CONNECTIONS 15

After unpacking the unit, and placing it on a solid

surface capable of supporting its weight, you will

need to make the connections to your audio and

video equipment.

Audio Equipment Connections

We recommend that you use high-quality inter-

connect cables when making connections to

source equipment and recorders to preserve the

integrity of the signals.

When making connections to audio source

equipment or speakers it is always a good prac-

tice to unplug the unit from the AC wall outlet.

This prevents any possibility of accidentally send-

ing audio or transient signals to the speakers

that may damage them.

1. Connect the analog output of a CD player to

the CD inputs

NOTE: When the CD player has both fixed and

variable audio outputs it is best to use the fixed

output unless you find that the input to the

receiver is so low that the sound is noisy, or so

high that the signal is distorted.

2. Connect the analog Play/Out jacks of a cas-

sette deck, MD, CD-R or other audio recorder to

the Tape Input jacks

. Connect the analog

Record/In jacks on the recorder to the Tape

Output jacks

on the AVR 4000.

3. Connect the output of any digital sources to

the appropriate input connections on the AVR

4000 front or rear panel. Note that the

Optical and Coaxial digital inputs

RS#%

may be used with a Dolby Digital

or DTS source or the output of a conventional

CD, MD or LD player’s PCM (S/P-DIF) output.

4. Connect the Coaxial or Optical Digital

Outputs

on the rear panel of the AVR to the

matching digital input connections on a CD-R or

MiniDisc recorder.

5. Assemble the AM Loop Antenna supplied with

the unit as shown below. Connect it to the AM

and GND screw terminals

6. Connect the supplied FM antenna to the FM

(75 ohm) connection

. The FM antenna may

be an external roof antenna, an inside powered

or wire lead antenna or a connection from a

cable system. Note that if the antenna or con-

nection uses 300-ohm twin-lead cable, you must

use a 300-ohm-to-75-ohm adapter to make the

connection.

7. Connect the front, center and surround speak-

er outputs

to the respective speakers.

To assure that all the audio signals are carried to

your speakers without loss of clarity or resolu-

tion, we suggest that you use high-quality

speaker cable. Many brands of cable are avail-

able and the choice of cable may be influenced

by the distance between your speakers and the

receiver, the type of speakers you use, personal

preferences and other factors. Your dealer or

installer is a valuable resource to consult in

selecting the proper cable.

Regardless of the brand of cable selected, we

recommend that you use a cable constructed of

fine, multistrand copper with an area greater

than 2 mm

Cable with an area of 1.5 mm

may be used for

short runs of less than 4 m.We do not recom-

mend that you use cables with an area less than

1mm

due to the power loss and degradation in

performance that will occur.

Cables that are run inside walls should have the

appropriate markings to indicate listing with UL,

CSA or other appropriate testing agency stan-

dards. Questions about running cables inside

walls should be referred to your installer or a

licensed electrical contractor who is familiar with

the applicable local building codes in your area.

When connecting wires to the speakers, be cer-

tain to observe proper polarity. Remember to

connect the “negative” or “black” wire to the

same terminal on both the receiver and the

speaker. Similarly, the “positive” or “red” wire

should be connected to like terminals on the

AVR 4000 and speaker.

NOTE: While most speaker manufacturers

adhere to an industry convention of using black

terminals for negative and red ones for positive,

some manufacturers may vary from this configu-

ration.To assure proper phase and optimal per-

formance, consult the identification plate on

your speaker or the speaker’s manual to verify

polarity. If you do not know the polarity of your

speaker, ask your dealer for advice before pro-

ceeding, or consult the speaker’s manufacturer.

We also recommend that the length of cable

used to connect speaker pairs be identical. For

example, use the same length piece of cable to

connect the front-left and front-right or sur-

round-left and surround-right speakers, even if

the speakers are a different distance from the

AVR 4000.

8. Connections to a subwoofer are normally

made via a line level audio connection from the

Subwoofer Output

to the line-level input

of a subwoofer with a built-in amplifier.When a

passive subwoofer is used, the connection first

goes to a power amplifier, which will be con-

nected to one or more subwoofer speakers. If

you are using a powered subwoofer that does

not have line-level input connections, follow the

instructions furnished with the speaker for con-

nection information.

Note: Speaker sets with two front satellites and

a passive subwoofer must be connected to the

front speaker outputs

only rather than to the

Subwoofer Output

Video Equipment Connections

Video equipment is connected in the same man-

ner as audio components. Again, the use of high-

quality interconnect cables is recommended to

preserve signal quality.To ensure best video per-

formance S-Video sources should be connected

to the AVR4000 only with their S-Video In/

Outputs, not with their composite video connec-

tors too.

1. Connect a VCR’s audio and video Play/Out

jacks to the Video 1 or Video 2 In jacks

2OQV

on the rear panel. The Audio and

Video Record/In jacks on the VCR should be con-

nected to the Video 1 or Video 2 Out jacks

4MPW

on the AVR 4000.

2. Connect the analog audio and video outputs

of a satellite receiver, cable TV converter or tele-

vision set or any other video source to the

Video 2

(if not in use) or Video 3

jacks.

3. Connect the analog audio and video outputs

of a DVD or laser disc player to the DVD jacks

4. Connect the digital audio outputs of a CD,

MD or DVD player, satellite receiver, cable box or

HDTV converter to the appropriate Optical or

Coaxial Digital Inputs

RS#%

5. Connect the Video Monitor Out

jacks on

the receiver to the composite and S-Video input

of your television monitor or video projector.

Video Connection Note:

• S-Video or Composite video signals may only

be viewed in their native formats and will not

be converted to the other format. But the OSD

will be viewed on the TV screen in any case,

with Video or S-Video input selected on the TV.

Installation and Connections

Harman Kardon AVR 4000 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 4000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info