Bedienungsanleitung Harman Kardon AVR 4000 (Seite 23 von 58) (Englisch)

8518

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

SYSTEM CONFIGURATION 23

40Hz, choose the frequency that is closest to the

upper frequency limit of your subwoofer.This fig-

ure is normally printed in the Owner’s Manual or

data sheet for the speakers, or consult the speak-

er’s manufacturer.

• When the front speakers have been set to

LARGE, the crossover choices are 40Hz

or 60Hzto match the typical crossover points

of full range speakers. Choose the option that is

closest to your speakers’ design.

• When the front speakers have been set to

SMALL, the crossover choices are

80Hzor 100Hzto match the typical

crossover points of the smaller speakers used in

satellite speaker systems. Choose the option that

is closest to your speakers’ design.

10. When all speaker selections have been made,

press the

¤ button

and then the Set button

to return to main menu.

11. The Speaker Configuration may also be

changed at any time without using the full-OSD

on-screen menu system by pressing the Speaker

Select button on the front panel

or remote

. Once the button is pressed, FNT

SPEAKER will appear in both the lower

third of the video display and the Main

Information Display

Within five seconds, either press the front panel

‹/› Selector buttons

or the ⁄/¤ buttons

on the remote to select a different speaker

position, or press the Set Button

begin the adjustment process for the front left

and right speakers

When the Set button

has been pressed

and the system is ready for a change to the front

speaker setting, the on-screen display and Main

Information Display Y will read FNT

LARGE or FNT SMALL depending on

the current setting. Press the front panel

‹/›

Selector Buttons

or the ⁄/¤ buttons

on the remote until the desired setting is shown,

using the instructions for “large” or “small”

shown earlier, then press the Set button

If another speaker position needs to be changed,

press the front panel

‹/› Selector buttons

or the ⁄/¤ buttons

on the remote to

select a different speaker position, press the Set

button

and then press the front panel

‹/› Selector buttons

or the ⁄/¤ buttons

on the remote until the correct speaker set-

ting is shown and press the Set button

again to confirm the selection.

To assist in making these settings, the icons in

the Speaker/Channel Input Indicators

will change as the speaker type is selected at

each position. When only the inner icon box is lit,

the speaker is set for “small.” When the inner box

and the two outer boxes with circles inside them

are lit, the speaker is set for “large." When no

indicator appears at a speaker location, that

position is set for “none” or “no” speaker.

Note: These icons are available only when mak-

ing setup changes in the semi-OSD mode.

As an example, in Figure 6 below, the left front

and right front speakers are set for “large,” the

center, left surround and right surround speakers

are set for small, and a subwoofer is set.

Figure 6

Adjustments for Other Inputs

After one input has been adjusted for surround

mode, digital input (if any) and speaker type,

return to the INPUT SETUP line on the

AUDIO SETUP menu and enter the set-

tings for each input that you will use. In most

cases, only the digital input and surround mode

will be different from one input to the next, while

the speaker type will usually be the same and

may be quickly entered by entering the same

data used for the original input.

Making Settings independent of

selected Input

After the settings described above have been

made for all input sources in your system, the

following settings, made with any input, will

remain in effect independent of the input

selected.

In order to set delay time for Dolby Digital and

Dolby Pro Logic surround modes, the OSD menu

system must be used.

Delay Settings

Only for the Dolby Digital or Dolby Pro Logic

modes, you will need to adjust the delay time

setting. Note that the delay time is not

adjustable for any other modes.

Important Note: Once the delay time is set

with any input it will be effective with all other

inputs too. Moreover the surround delay time

setting must be made only for either the Dolby

Pro Logic or the Dolby Digital mode. The other

setting will be set automatically.

Due the different distances between the listening

position for the front channel speakers and the

surround speakers, the amount of time it takes

for sound to reach your ears from the front or

surround speakers is different. You may compen-

sate for this difference through the use of the

delay settings to adjust the timing for the specific

speaker placement and acoustic conditions in

your listening room or home theater.

The factory setting is appropriate for most rooms,

but some installations create an uncommon dis-

tance between the front and surround speakers

that may cause the arrival of front channel

sounds to become disconnected from surround

channel sounds.

To resynchronize the front and surround chan-

nels, follow these steps:

1. Measure the distance from the listening/ view-

ing position to the front speakers in meters.

2. Measure the distance from the listening/ view-

ing position to the surround speakers.

3. Subtract the distance to the surround speakers

from the distance to the front speakers and

multiply the result by 3.

a.When setting the delay time for the Dolby

Digital surround modes, the optimal delay time

is the result of that subtraction. For example, if

the front speakers are 3 m away and the sur-

round speakers are 1 m away, the optimal

delay time is figured as (3–1)x3=6. Thus, in

this example, the delay time for Dolby Digital

should be set at six milliseconds.

b. When setting the delay time for the Pro Logic

mode, take the result of the subtraction and

add 15 to obtain the optimal delay time. For

example, if the front speakers are 3 m away

System Configuration

Harman Kardon AVR 4000 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR 4000

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info