502627

Harman Kardon AVR 5000 Seite 25

25
Zoom out
Zoom in
Vorherige Seite
1/58
Nächste Seite
SYSTEM CONFIGURATION 25
System Configuration
Using EzSet
Harman Kardon’s exclusive EzSet remote makes
it possible to quickly and accurately set the
AVR5000’s output levels without the use of a
sound pressure meter, although manual adjust-
ment is also available. However, for the easiest
set-up, follow these steps while seated in the lis-
tening position that will be used most often:
1. Make certain that all speaker positions have
been properly configured for their “large” or
“small” settings (as outlined above) and turn off
the OSD system if it is in use.
2. Adjust the volume so that it is at -15,as
shown in the on-screen display or Main
Information Display
Y
.
3. Select any input associated with the Dolby Pro
Logic surround mode. Remember to make the
same adjustment with all other surround modes
you´ve associated with the inputs used.
4. First a non-automatic pre-test should be
made: Turn on the internal test tone by pressing
the Test tone button
8
. You will hear a test
noise circulate from speaker to speaker in a
clockwise direction around the room.
Listen to make certain that the sound comes
from the speaker position shown in the Main
Information Display
Y
. If the sound from a
speaker location does NOT match the position
indicated, turn the AVR5000 off using the Main
Power Switch
1
and check the speaker
wiring to make certain that each speaker is con-
nected to the correct output terminal.
5. Hold the remote in front of you at arm’s
length, making sure not to cover the EzSet
Sensor Microphone
c
at the top of the remote
and aim it at the AVR5000, not vertically (like
you’d do with a microphone).
6. Press and hold the SPL Indicator Select
Z
for three seconds. Release the button when
the Program/SPL Indicator
2
stops flashing
and you hear the test noise from the front left
speaker.
7. At this point, the EzSet circuitry will take over,
adjusting the output level of each channel so
that when the process is complete all levels will
be equal and at the set reference point. This
process may take a few minutes, depending on
the extent of adjustment required.
8. During the adjustment you will see the loca-
tion of the channel position being adjusted
appear in both the on-screen display (if connect-
ed) and the Main Information Display
Y
,
alternating with a readout of the output setting,
relative to the reference volume level. As the
adjustment proceeds, a few things will happen
simultaneously:
• The channel position being adjusted will flash
in the Speaker/Channel Position Indicators
Q
. If the test noise is heard from a channel
other than the one shown in the Indicator, there
is an error in the speaker connections. If this is
the case, press the Test Button
8
TWICE to
stop the adjustment. Then, turn the unit off and
verify that all speakers are connected to the
proper Outputs
DE
.
• When the front left channel is being set at the
beginning of the process, EzSet will adjust the
main volume level, as shown by the indication of
the FRONT L LEValternating in the on-
screen display (if connected) and the Main
Information Display
Y
with the volume indi-
cation. During the adjustment, the test tone may
seem to pulse, or click, as EzSet changes the
level. This is a normal aspect of the system’s
operation.
• As the other channels are set, the channel
name and the adjustment offset will appear in
the on-screen display (if connected) and the
Main Information Display
Y
. While the level
is changing, the Program/SPL Indicator
2
will change colors to reflect the output level in
relation to the reference. A red indication shows
that the level is too high, while an amber indica-
tion shows that the level is too low. When the
Indicator is green, the level is correct, and the
test noise will move to the next channel.
• While adjustments are being made, the red
LED under the AVR Selector
5
will flash.
This is normal, and indicates that EzSet is oper-
ating.
9. After the test noise has circulated once
through each channel, it will send the tone to
the front left channel once again, to finally
adjust its output level.
10. Upon completion of the front left channel
adjustment, the Program/SPL Indicator will flash
green three times and then go out. The tone will
stop and the AVR5000 will return to normal
operation.
Manual Output Level Adjustment
Output levels may also be adjusted manually,
either to set them to a specific level with an SPL
meter, or to make fine tuning adjustments to the
levels obtained using the EzSet remote.
Manual output level adjustment is most easily
done through the OUTPUT ADJUST
menu (Figure 7). If you are already at the main
menu, press the
¤ buttons
D
until the on-
screen
› cursor is next to the OUTPUT
ADJUST line. If you are not at the main
menu, press the OSD button
L
to bring up
the MASTER MENU (Figure 1), and then
press the
¤ buttons
D
three times so that the
on-screen
› cursor is next to the Output adjust
line. Press the Set button
F
to bring the
OUTPUT ADJUST menu (Figure 7) to
the screen.
Figure 7
As soon as the new menu appears, you will hear
a test noise circulate from speaker to speaker in
a clockwise direction around the room. The test
noise will play for two seconds in each speaker
before circulating, and a blinking on-screen cur-
sor will appear next to the name of each speaker
location when the sound is at that speaker. Now
turn up the volume until you can hear the noise
clearly.
IMPORTANT NOTE: Because this test noise will
have a much lower level than normal music, the
volume must be lowered after the adjustment
for all channels is made, but BEFORE you return
to the main menu and the test tone turns off.
After checking for speaker placement, let the
test noise circulate again, and listen to see
which channels sound louder than the others.
Using the front left speaker as a reference, press
the
‹/› buttons
EU
on the remote to bring
all speakers to the same volume level. Note that
when one of the
‹/› buttons is pushed, the test
noise circulation will pause on the channel being
adjusted to give you time to make the adjust-
ment.When you release the button, the circula-
tion will resume after five seconds. The on-screen
cursor
› can also be moved directly to the
speaker to be adjusted by pressing the
⁄/¤
buttons
D
on the remote.
* OUTPUT ADJUST *
FRONT LEFT : 0dB
CENTER : 0dB
FRONT RIGHT: 0dB
SURR RIGHT : 0dB
SURR LEFT : 0dB
RETURN TO MENU
… 25 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

harman-kardon-avr-5000

Suche zurücksetzen

  • nach dem einschalten wird das display dunkel bei harman stereoanlage
    Eingereicht am 12-5-2022 06:51

    Antworten Frage melden

  • Ich bin im Besitz der neuen UPC Box. Möchte den Ton über meinen Harmon Cardon Resiver AVR 5000 steuern. Leider kann ich den Resiver nicht auf Dgital umschalten, er überhüpft Ihn. Muss der Antennenanschluss auch digital sein?
    Freundliche Grüsse

    Stefan Scherrer

    steven.scherrer@bluewin.ch Eingereicht am 9-2-2019 11:45

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Harman Kardon AVR 5000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Harman Kardon AVR 5000

Harman Kardon AVR 5000 Bedienungsanleitung - Deutsch - 60 seiten

Harman Kardon AVR 5000 Bedienungsanleitung - Holländisch - 58 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info