Bedienungsanleitung Harman Kardon AVR146 (Seite 45 von 60) (Englisch)

502586

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ADVANCED FUNCTIONS

System Settings

The AVR 146 offers several system settings that allow you to make the

receiver easier to use rather than directly affecting performance. Most of

these settings may be accessed from the SYSTEM SETUP menu, which

is selected by pressing the OSD Button and navigating to the SYSTEM

SETUP line of the MASTER MENU. Press the Set Button to display the

submenu. See Figure 73.

Figure 73 – System Setup Menu Screen

VFD FADE TIME OUT: Some people find the brightness of the AVR’s

front-panel display distracting during movies or listening sessions. It’s

possible to dim the front-panel display completely using the Dim function

(see below). This sets the display to remain dark most of the time, lighting

up only when a button is pressed or a remote command is received,

and going dark again 5 seconds after the last command. The VFD

FADE TIME OUT feature also causes the display to light up only when

a button is pressed or a change in the incoming signal is detected, but

the display immediately begins to fade to dark. This setting allows you

to program the length of the fade time.

Select a time-out period of between 3 and 10 seconds, or select

OFF if you prefer to leave the displays on at all times or to use the

Dim function.

VOLUME DEFAULT and DEFAULT VOL SET: These two settings are

used together to program a volume level the AVR will always switch to

when turned on. This feature avoids discomfort for listeners in case the

last user turned the volume very high.

Press the OSD Button to remove the display from the screen so that

you may adjust the volume to a desired level while a source is playing.

Make a note of the number that appears in the display, and return to

the SYSTEM SETUP menu. At the DEFAULT VOL SET line, select the

desired volume setting, and activate the feature by setting VOLUME

DEFAULT to ON.

NOTE: Although volume is normally displayed in 0.5dB incre-

ments, the default volume setting only allows whole numbers.

SEMI OSD TIME OUT: At this line you may program the amount of

time (2 to 5 seconds) the two-line semi-OSD on-screen messages

remain, or you may deactivate the semi-OSD display altogether if you

find it distracting. These messages will continue to appear on the front

panel of the receiver.

FULL OSD TIME OUT: At this line you may program the amount of

time (20, 30, 40 or 50 seconds) the full-OSD menus remain visible

on screen. The full-OSD system may not be deactivated.

DEFAULT SURR MODE: This setting determines how the AVR 146 will

handle Dolby Digital and DTS sources. For the purposes of this setting,

the “default surround mode” means the mode encoded in the program,

such as Dolby Digital 5.1. With this setting ON, the receiver will always

use the default surround mode encoded in the program. When this

setting is changed to OFF, the receiver will use the surround mode

you selected the last time this type of audio stream was detected.

Dolby Digital 2.0 signals default to the Dolby Pro Logic II Movie mode,

but you may select another Dolby surround mode manually. For PCM

and analog sources, the factory default surround mode is Logic 7

Music. In general, the receiver will use the surround mode selected

the last time that type of signal was received.

OSD BACKGROUND: This setting allows you to choose between a

blue or black background for the full-OSD menus.

NOTE: It isn’t possible to view video sources while the full-OSD

menus are displayed.

Dim Function

Some people find the front-panel messages to be distracting and would

prefer to dim them or turn them off altogether. When the display is

dimmed or darkened, it will return to full brightness for five seconds

any time a command is received before dimming or darkening again.

To dim the display:

Press the Dim Button on the remote. Each button press will cycle

through the three settings of:

VFD FULL: Normal brightness

VFD HALF: Display is dimmed but still visible; the light inside the

volume knob goes dark

VFD OFF: Display goes completely dark except for Power Indicator

to remind you that the receiver is turned on

Advanced Remote Control Functions

The remote control not only operates the AVR 146, but it also serves

as a universal remote that may be programmed to operate many of your

other home theater components, as described in the Installation section.

Each time you select one of your other components, the AVR remote

switches to the control functions for that component. Since many buttons

have unique functions for each component, refer to the Function List in

the Appendix for assistance in operating your other components. The

function of each button will not necessarily correspond to the label printed

on the button.

Punch-Through Programming

The AVR 146 remote’s punch-through feature allows you to select

one component for the remote to operate, while simultaneously setting

AVR146-OM.qxd 5/10/07 10:17 AM Page 45

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR146 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info