Bedienungsanleitung Harman Kardon AVR254 (Seite 8 von 76) (Englisch)

502597

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

FRONT-PANEL CONTROLS

Main Power Switch: This mechanical switch turns the power supply

on or off. It is usually left pressed in (On position), and cannot be turned

on using the remote control.

Standby/On Switch: This electrical switch turns the receiver on

for playback, or leaves it in Standby mode for quick turn-on using this

switch or the remote control.

Power Indicator: This LED has four possible modes:

• Main Power Off: When the AVR is unplugged or the Main Power

Switch is off, this LED is off.

• Standby: The LED is amber, indicating that the AVR is ready to

be turned on.

• On: The LED is white, when the AVR is on and operating normally.

• Protect: If the PROTECT message ever appears, turn off the AVR

and unplug it. Check all speaker wires for a possible short. If none is

found, bring the unit to an authorized Harman Kardon service center

for inspection and repair before using it again.

Source List: Press this button to select a source device, which

is a component where a playback signal originates, such as DVD,

cable TV, satellite or the tuner.

Volume Knob: Turn this knob to raise or lower the volume.

Message Display: Various messages appear in this two-line display

in response to commands and changes in the incoming signal. In normal

operation, the current source name appears on the upper line, while the

surround mode is displayed on the lower line. When the on-screen dis-

play menu system (OSD) is in use, the current menu settings appear.

Headphone Jack/EzSet/EQ Microphone Input: Plug a 1/4"

headphone plug into this jack for private listening.

This jack is also used to connect the supplied microphone for the

EzSet/EQ procedure described in the Initial Setup section. To begin

EzSet/EQ, plug the supplied microphone into this jack, place the micro-

phone at the listening position, and follow the directions given in the

Speaker Setup-Automatic Setup-EzSet/EQ on-screen menu.

Surround Modes: Press this button to select a surround sound

(e.g., multichannel) mode. The Surround Modes menu will appear on

screen, and the menu line will appear in the front-panel display.

Use the front-panel or remote

⁄

Buttons to highlight a different

menu line: Auto Select, Virtual Surround, Stereo, Movie, Music or Video

Game. Each line represents a type of audio signal, and is set to the

preferred surround mode that you manually select.

Press the OK Button when the menu line is highlighted, and the

available surround mode options for the current signal will appear.

Use the

⁄

Buttons to select the desired mode, and press the

OK Button to engage it. Press the Back/Exit Button to exit the Surround

Modes menu.

See the Advanced Functions section for more information on surround

modes.

Analog Audio, Video and Digital Audio Inputs: Connect a

source component that will only be used temporarily, such as a digital

camera or game console, to these jacks. Use only one type of audio

and one type of video connection.

NOTES:

• Each of these connections (analog audio, digital audio and

video) may be independently assigned to any source. See the

Initial Setup section for information on setting up sources,

including assigning audio and video inputs to a source.

• Although these jacks are labeled Optical 3, Coaxial 3 and

Video 4 on the AVR, the AVR’s menus refer to them as the

Optical Front, Coaxial Front, Composite Front, S-Video Front

and Analog Front inputs.

Speaker/Channel Input Indicators: The box icons indicate

which speaker positions you have configured (see the Initial Setup

Section), and the size (frequency range) of each speaker. The letters

will light inside the boxes to indicate which channels are present in

the incoming signal.

Navigation: These buttons are used to navigate the AVR’s menus

and to operate the tuner.

Remote IR Sensor: This sensor receives infrared (IR) commands

from the remote control. It is important to ensure that it is not blocked.

If covering the sensor is unavoidable, such as when the AVR 254 is

placed inside a cabinet, you may use an optional Harman Kardon

HE 1000, or other infrared receiver, connecting it to the Remote IR

Input on the AVR 254’s rear panel. Alternatively, connect the Remote IR

Output of another compatible component to the AVR 254’s Remote

IR Input. Point the remote at the other device’s remote sensor, and the

command will be transmitted to the AVR 254. An external IR “blaster”

may also be used, positioned to point at this area.

AVR Settings Button: Press this button to access the AVR’s

main menu.

Info Settings Button: Press this button to directly access the

AVR’s Source Info submenu, which contains the settings for the

current source.

Resolution: Each press of this button changes the AVR’s video output

resolution to these settings: 480i, 480p, 720p, 1080i or 1080p.

IMPORTANT NOTE: If the AVR’s video output resolution is set

higher than the capabilities of the actual connection, you will not

see a picture. If the best video connection from the AVR to the

TV is either composite or S-video, press this button until the

resolution is set to 480i.

AVR254om.qxd 3/28/08 12:45 PM Page 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR254 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info