Bedienungsanleitung Harman Kardon AVR254 (Seite 30 von 76) (Englisch)

502597

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

INSTALLATION

from the appendix table corresponding to the device and pro-

gram it into the AUX Source Selector. Similarly, the CBL/SAT

Source Selector is used for either a cable or satellite television

set-top box. The first digit of the product code indicates the

device type.

2. Turn on your source device.

3. This step places the remote in program mode. Refer to Figure 37.

Press and hold the Source Selector. The button will turn red, then go

dark. Continue holding it, and when it turns red again, release the

button; the remote is now in program mode. Follow the directions in

Step 4, below.

Figure 37 – Source Selectors

Optional: To reassign a device type from one Source Selector to another

Source Selector not being used, e.g. if there are two DVD players in the

system, press the Source Selector for the new device type now. For

example, to reassign the Cable/Sat Source Selector to operate a DVD

player, first press and hold the Cable/Sat Button, and then press the

DVD Button.

4. Enter a code from Step 1, above.

a) If the device turns off, press the Source Selector again to accept

the code; it will flash. The remote will exit Program mode.

b) If the device does not turn off, try entering another code. If you

run out of codes, you may search through all of the codes in the

remote’s library for that product type by pressing the

⁄

Button repeatedly until the device turns off. When the device turns

off, enter the code by pressing the Source Selector, which will

flash. The remote then exits Program mode.

5. Once you have programmed a code, it’s a good idea to try using

some other functions to control the device. Sometimes, manufacturers

use the same Power code for several different models, while other

codes will vary. You may wish to repeat this process until you’ve

programmed a satisfactory code set that operates most of the

functions you frequently use.

6. Find out which code number you have programmed by pressing

and holding the Source Selector to enter the Program mode. Then

press the OK Button, and the Source Selector will flash in the code

sequence. One flash represents “1”, two flashes for “2”, and so forth.

A series of many fast flashes represents “0”. Record the codes pro-

grammed for each device in Table A9 in the appendix.

If you are unable to locate a code set that correctly operates your

source device, it will not be possible to use the AVR remote to control

that device. However, you may still connect the source to the AVR 254

and operate it using the device’s original remote control.

Most of the button labels on the remote describe the button’s function

when used to control the AVR 254. However, the button may perform

a very different function when used to control another device. Refer to

the Remote Control Function List, Table A13 in the Appendix, for a list of

each button’s functions with the various product types.

If you wish, you may program Activities, which are preprogrammed code

sequences that execute many code commands with a single button

press. You may also program “punch-through” codes, which allow the

remote to operate the channel or transport controls of another device

without having to switch the remote’s device mode. See page 53 for

instructions on these advanced programming functions.

Step Nine – Remote IR Inputs and Output (Optional)

The AVR 254 is equipped with a Remote IR Input, a Zone 2 Input and

a Remote IR Output to facilitate use of your system with a remote control

in a variety of situations. See Figure 38.

Figure 38 – IR Inputs and Outputs

When the AVR 254 is placed in such a way that aiming the remote at the

front-panel IR sensor is difficult, such as inside a cabinet or facing away from

the listener, you may connect an external IR receiver, such as the optional

Harman Kardon HE 1000, to the Remote IR Input jack. When you are using

the AVR 254 in multizone mode, you may connect an optional IR receiver,

keypad or other control device to the Zone 2 IR Input for remote control

of the AVR 254 (and any sources connected to the AVR’s Remote IR

Output) from the remote zone. Any signals transmitted through the Zone 2

IR Input will only control source selection and volume for the remote zone.

If a source device is being shared with the main listening area, then any

control commands issued to that source will also affect the main room.

If any of your source devices are equipped with a compatible Remote

IR Input, use a 1/8" mini-plug interconnect cable (not included) to con-

nect the AVR’s Remote IR Output to the source device’s Remote IR

Input, which will pass any applicable remote signals transmitted through

the AVR to the source device. This enables you to control your sources

even when the AVR itself is controlled via an external IR receiver.

Check with the manufacturer of the source device for more information

on the type of IR signal expected. The AVR 254 will output a “stripped

carrier” IR signal through the Remote IR Output.

AVR 254

AVR254om.qxd 3/28/08 12:46 PM Page 30

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR254 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info