Bedienungsanleitung Harman Kardon AVR254 (Seite 50 von 76) (Englisch)

502597

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

blocks, change the MPEG Noise Reduction setting from its default of

Off to the Low, Medium or High setting to improve the picture.

Cross Color Suppressor: Turn this setting on to remove cross color

artifacts, which can occur when high-frequency luminance (brightness)

signals are misinterpreted as chroma (color) signals, which can cause

unwanted flickering, flashing colors or rainbow patterns.

Film Mode Detect: While normally left off, turn this setting on to com-

pensate for authoring errors in the process of converting film programs

to video.

How to Adjust the Custom Picture Settings

Set the Video Mode to Custom to display the picture settings as shown

in Figure 68.

Figure 68 – Video Modes Custom Processing

With a color bar test pattern screen from a test disc or other source

showing on your video display, the following adjustments may be made:

• The proper color intensity setting on your TV.

• Proper color adjustments using the color bars, which should be (left

to right) black, white, yellow, cyan (turquoise), green, magenta, red,

blue, black.

• The proper color transition, seen as sharp separation of the bars.

• The performance of the color circuits in your TV (with “Video” signals);

bar edges should show no vertical crawling dots.

With the gray scale and the black/white fields below the color bars, the

brightness and contrast of your screen can be adjusted.

Brightness Adjustment

1. Turn down the color control on your TV until the color bars appear

in black and white.

2. Adjust the contrast to the lowest level where you still can see all gray

scale bars separately and clearly.

3. Adjust the brightness so that the bars in the gray scale are all visible.

The bar farthest to the left has to be as black as possible rather than

gray but the next gradation must clearly be distinct from it. All the

bars in the gray scale should be gradually and evenly changing from

black to white, left to right.

Contrast Adjustment

1. Adjust the contrast on your TV until you see a bright white bar in the

lower right corner of the screen and a deep-dark-black bar to the

left. The optimal contrast setting will depend on your preference and

the surrounding light in the TV room.

2. If the brightness of the white bar no longer increases when the con-

trast is turned up or the borders of white letters bloom (overlight) into

the black areas (drastically decreasing the sharpness of the type), the

contrast has been turned up too much. Reduce the contrast until

these effects disappear and the video still looks realistic.

3. If you are watching TV with ambient daylight, adjust the contrast so

that a normal video picture has about the same look as the surround-

ings in your room. That way the eye is relaxed when watching the TV

picture. This contrast setting may be reduced when the surrounding

light is dimmed, thereby usually improving the sharpness of a video

significantly.

4. The gray scale in the middle line needs to have the same clear

difference between each bar as before the contrast adjustment. If

not, go back to “Brightness Adjustment” and repeat Step 3 and then

“Contrast Adjustment,” making only minor adjustments each time for

optimization.

Color Adjustment

1. When the brightness and contrast are set optimally, adjust the color

control to the level of your preference. Set the level so that the colors

look strong but still natural, not overdone. If the color level is too

high, depending on the TV, some of the bars will seem wider or the

color intensity will not increase when the control is turned up. Then

the color control must be reduced again. Ultimately, you also should

test the color intensity with a video – e.g., pictures of natural faces,

flowers, fruit and vegetables, and other common natural articles for

an optimal setting of the color intensity.

2. Refer to the large white bar below the gray scale to tweak the

warmth of the picture. Every viewer has a preference as to how the

glow of the picture should be. Some prefer a colder picture, some

a warmer glow. The Tint function on your TV and the white bar can

be used to control this. Adjust the Tint to the level where you feel

the white color has the tone you prefer.

Sharpness Adjustment

Contrary to intuition, the picture will appear sharper and clearer with the

sharpness backed off from the maximum setting. Reduce the sharpness

setting on your television, and the setting on the AVR 254 if necessary,

to minimize the appearance of any white lines between the bars in the

gray scale portion of the test screen.

Convergence and Edge Focus

The crosshatch pattern that surrounds the test screen may be used to

evaluate edge focus and convergence in front- or rear-projection video

displays. However, the controls used to adjust these parameters are

often not user-accessible. In any event, these adjustments are extremely

ADVANCED FUNCTIONS

AVR254om.qxd 3/28/08 12:46 PM Page 50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR254 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info