Bedienungsanleitung Harman Kardon AVR255 (Seite 7 von 58) (Englisch)

502550

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Volume Control: Turn this knob clockwise

to increase the volume, counterclockwise to

decrease the volume. If the AVR is muted,

adjusting volume control will automatically

release the unit from the silenced condition.

System Power Control: When the Main

Power Switch on the rear panel is “ON,” press

this button to turn on the AVR; press it again to

turn the unit off (to Standby). Note that the

Power Indicator

will turn white when the

unit is on.

Power Indicator: This LED will be illuminated

in amber when the unit is in the Standby mode

to signal that the unit is ready to be turned on.

When the unit is in operation, the indicator will

turn white.

Headphone Jack: This jack may be used to

listen to the AVR’s output through a pair of head-

phones. Be certain that the headphones have a

standard 6,3 mm stereo phone plug. Note that

the speakers will automatically be turned off

when the headphones are connected.

When configuring your system using EzSet/EQ,

the calibration microphone should be plugged

into this jack using the supplied adaptor that

converts the small mini-plug at the end of the

microphone’s cord to a 6,3 mm plug.

Navigation: These buttons are used to navi-

gate the AVR’s menus and to operate the tuner.

OK Button: Press this button to select the

currently highlighted item.

AVR Settings Button: Press this button to

access the AVR’s main menu.

Info Settings Button: Press this button to

directly access the AVR’s Setup Source submenu,

which contains the settings for the current

source.

Resolution: Pressing this Button once and

then using the Up/Down Navigation Buttons

changes the AVR’s video output resolution to

these settings: 576i, 576p, 720p, 1080i or

1080p. The AVR is set to default to 576i when

first switched on, or if you reset it later. This reso-

lution has been chosen to ensure that the On

Screen Display information is visible on your TV

even with analog S-Video or Composite (CVBS)

signals. Having selected the best resolution for

your system, confirm with the OK Button

. The

Front Panel Display now shows "Res Change,

Cancel". If you press OK now, or do nothing for

20 seconds, the AVR returns to normal play

mode. To confirm the new resolution, press the

L Button

, which changes the Display from

"Cancel" to "Accept", then press the OK Button

. The new resolution is now in use.

)

Audio Effects: Press this button to directly

access the Audio Effects submenu, which allows

adjustment of the tone and other controls. See

the Initial Setup section for more information.

Video Modes: Press this button for direct

access to the Video Modes submenu, which con-

tains settings that may be used to improve the

picture if necessary after you have adjusted the

picture settings using the video display or TV.

@ Source List Button: Press this Button to

open the on-screen Source Selection Menu with

the slide-in Source List already open. If you are

not using your TV for on-screen reference, use

the Front Panel Information Display which shows

the information you need. Scroll up and down

with the KL Buttons

, select the desired

Input by pressing the OK Button

and exit the

Source Selection function by pressing the Source

List Button

again.

Main Information Display: This display

delivers messages and status indications to help

you operate the receiver.

Speaker/Channel Input Indicators: These

indicators are multipurpose, indicating either the

speaker type selected for each channel or the

incoming data-signal configuration. The left, center,

right, right surround and left surround speaker

indicators are composed of three boxes, while the

subwoofer is a single box.The center box lights

when a “Small” speaker is selected, and the two

outer boxes light when “Large” speakers are

selected.When none of the boxes are lit for the

center, surround or subwoofer channels, no speaker

has been selected for that position. (See page 22

for more information on configuring speakers.) The

letters inside each of the center boxes display

active input channels. For standard analog inputs,

only the L and R will light, indicating a stereo

input. When a digital source is playing, the indica-

tors will light to display the channels being

received at the digital input. When the letters

flash, the digital input has been interrupted.

(See page 33 for more information on the Channel

Indicators).

NOTE: When you have reassigned the surround

back speakers to the remote zone using the

MULTI ROOM SETUP menu, the boxes that

indicate the presence of the surround back speak-

ers will automatically disappear, reflecting the fact

that the main listening area is now configured for

5.1-channel operation. (See page 35 for more

information on reassigning the surround back

speakers for multiroom use.)

Surround Modes: Press this button to

select a surround sound (e.g.,multichannel)

mode. The Surround Modes menu will appear on

screen, and the menu line will appear on the

lower line of the front-panel display.

Use the front-panel or remote K/L Buttons to

highlight a different menu line:Auto Select,

Virtual Surround, Stereo, Movie, Music or Video

Game. Each line represents a type of audio sig-

nal, and is set to the surround mode the AVR will

automatically select when it detects the audio

ignal.

You may manually select a different mode for

each type of audio. Press the OK Button when

the menu line is highlighted, and the available

surround mode options for the current signal will

appear. Use the K/L Buttons to select the

desired mode, and press the OK Button to

engage it. Press the Back/Exit Button to exit the

Surround Modes menu and display the next high-

er menu in the hierarchy.

See the Advanced Functions section for more

information on surround modes.

Back/Exit: Press this button to return to the

previous menu.When the main AVR menu is dis-

played, press this button to exit the menu system.

Digital Optical Front Input: Connect the

optical digital audio output of an audio or video

product to this jack.

Digital Coax Front Input: This jack is nor-

mally used for connection to the output of

portable digital audio devices, video game con-

soles or other products that have a coax digital

jack.

(

Video Front Input Jacks: These

audio/video jacks may be used for temporary

connection to video games or portable

audio/video products such as camcorders and

portable audio players.

Ó Remote Sensor Window: The sensor

behind this window receives infrared signals from

the remote control. Aim the remote at this area

and do not block or cover it unless an external

remote sensor is installed.

Front Panel Controls

ENGLISH

FRONT PANEL CONTROLS 7

Harman Kardon AVR255 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR255

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info