Bedienungsanleitung Harman Kardon AVR255 (Seite 21 von 58) (Englisch)

502550

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

System Configuration

ENGLISH

SYSTEM CONFIGURATION 21

Audio and Video Input Selection

Please see Table A1 in the appendix for the fac-

tory default input assignments for each source.

You may assign any available input to any

ource using the Source Info menu, accessible

either by pressing the AVR Settings Button Y

and selecting the Setup Source line, or by press-

ing the Info Settings Button Y for direct access.

When a source is selected, the AVR will check

he assigned digital audio input for a signal. If

one is present, the digital input will be selected.

If not, the AVR will select the analog audio input

specified at the Audio Auto Polling line of the

Setup Source menu. If you don’t want the AVR

to select an analog audio input for the source,

change this setting to Off.

The AVR will also select the assigned video

source. There are no “Audio Only” sources on

the AVR, other than the Radio, which uses a spe-

cial on-screen menu. If no video signal is pres-

ent, the display will remain black. You may pair

an audio device with an A/V device’s video sig-

nal using the Source Info menu as explained in

the Initial Setup section. Sources may share

audio or video inputs to suit your application.

Set Up Sources

The Source Info menu is used to assign the

correct physical audio and video connections to

each source. It also provides access to a variety

of other settings, many of which may be

adjusted later as you become more familiar with

the AVR.

The following settings are not optional and must

be adjusted now to enable playback of each

source: Video Input from source, Audio Input

from Source and Resolution to Display.

The other settings may be adjusted at any time

to improve performance.

To display the Source Info menu, press the Info

Settings Button (front panel 7 or remote Y). A

screen similar to the one shown in Figure 2 will

appear. This screen may also be accessed from

the Main Menu by selecting the Setup Source

line and selecting a source from the slide-in

menu.

Figure 2 – Setup Source Menu

Audio Effects: Select this line to display the

Audio Effects submenu, where you may: adjust

the bass and treble tone controls; adjust the LFE

trim; activate the saved EzSet/EQ settings or

adjust the night mode setting. It is

recommended that you leave this submenu at its

default settings, and return to it later if your

system requires any fine-tuning.

See the Advanced Functions section for more

information.

Video Modes: Select this line to display the

Video Modes submenu, where you select from

preprogrammed or custom picture settings and

make picture adjustments. It is recommended

that you leave the settings at their factory

defaults. Picture adjustments should be made to

your video display first, with this menu used only

for fine-tuning.

See the Advanced Functions section for more

information.

Surround Mode: Select this line to display the

Surround Mode submenu, where you may

program the desired surround mode for various

types of analog programs, including movies,

music and games. You may also specify a specific

stereo mode (depending on the number of

channels desired) and a virtual surround mode if

your system uses fewer than the full

complement of seven main speakers (plus a

subwoofer).

Digital surround signals, such as Dolby Digital

and DTS programs, are automatically played in

their native formats, although you may change

the surround mode at any time.

See the Advanced Functions section for

information on surround modes available with

digital programs.

In the factory default Auto Select mode, the AVR

will analyze the source signal and select the

optimum playback mode. At the factory the AVR

was programmed to use Logic 7 Movie mode for

optimal playback of movies, including television

programs; Logic 7 Music mode for music

recordings, such as CDs; and Logic 7 Game

mode when a video game console is in use.

Audio Format From Source: This line is

informational only. When a digital program is

playing, its format will be identified here. When

analog audio programs are playing, this line

indicates NO AUDIO INPUT, referring to digital

inputs only.

Video Input from source: Select this line to

assign the correct video input to the source.

Refer back to Table A5 in the appendix, where

you noted the physical video input the source is

connected to, and select the input here.

Audio Input from source: Select this line to

assign the correct analog or digital audio input

to the source. Refer back to Table A5 in the

appendix, where you noted the physical audio

input the source is connected to, and select the

input here. If both analog and digital audio

connections were made, select the digital input

here, and select the analog input at the Audio

Auto Polling line below.

NOTE: For sources connected to an HDMI Input,

the Video and Audio Input settings should

indicate the same HDMI connection.

Resolution to Display: This line reflects the

video output resolution, which is dependent

upon the capabilities of the video display.

NOTE: When using the AVR’s on-screen menu

system, we recommend selecting a video output

resolution of 720p or higher for best legibility,

and to provide graphics that simplify some

configuration options. Depending on the

resolution selected, the menus shown by your

system may vary in appearance.

• If the display is connected to the AVR’s

Composite or S-Video Monitor Output, the video

output resolution must be manually set to 576i

to view any content, including the AVR’s own

menus. The AVR's default resolution is set to

576i.

Since there is no picture if the resolution is set

higher than the display’s capability, or if the

HDMI system does not automatically select the

best resolution, in these cases you must adjust

the resolution by pressing the front-panel

Resolution Button followed by the Up/Down

Buttons 3 until the correct setting appears on

the Lower Line of the front-panel Message

Display and confirm with the OK Button 5. The

Display now shows CANCEL, and you must scroll

to have the Display show ACCEPT with the

Up/Down Buttons 3 and then press OK to

make the new Resolution take effect. If you

press OK when CANCEL is on the screen, or if

you do nothing, the Resolution remains as it was

before. For composite and S-video, the correct

setting is 576i. For component video, it is the

highest resolution where a picture is visible.

Harman Kardon AVR255 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR255

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info