Bedienungsanleitung Harman Kardon AVR255 (Seite 44 von 58) (Englisch)

502550

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

Programming the Remote

ctivity Programming (Macros)

Activities enable you to easily repeat frequently

used combinations of commands with the press

of a single button on the AVR’s remote control.

Once programmed, an Activity will send out up to

19 different remote codes in a pre-determined

sequential order enabling you to automate the

process of turning on your system, changing

devices, or other common tasks. The AVR’s

remote can store up to eleven separate activity

command sequences, one that is associated with

the AVR Power On button

, and ten more

that are accessed by pressing the 0-9 Buttons

. To start programming an activity, press the

Activity button

and one of the 0-9 buttons

to be programmed or the AVR Power On

button

at the same time. Note that the latest

selected Device LED will light red.

2. Enter the steps for the activity sequence by

pressing the button for the actual command

step. Although the activity may contain up to 19

steps, each button press, including those used to

change devices, counts as a step. The Device

LED will blink once to confirm each button press

as you enter commands.

• Remember to press the appropriate Input

Selector button

before functions are

changed to another device. This is also needed

for the AVR Selector button

itself, as long

as it’s not lit red and AVR functions shall be

programmed.

3. When all the steps have been entered, press

the Activity button

again to enter the

commands. The red light under the Input

Selector

will blink three times and then

turn off.

Note: It can take up to 10 seconds to send out

19 commands from an Activity Button. Please

continue to point the remote control at the

device(s) until all the commands on the Activity

Button have been sent out. This will ensure that

all the commands are received by the device(s).

Example: Activity Button Programming.

To program Activity Button “2” to send the fol-

lowing commands: turn on the Audio receiver,

turn on the TV, turn on a DVD, and turn on a

Satellite receiver.

Press the Activity Button “2” and the ACTIVITY

button, simultaneously.

Press the AVR device button(to change to the

AVR mode)

Press the AVR POWER ON button(to turn on the

Audio receiver)

Press the TV device button(to change to the TV

mode)

Press the DEVICE POWER ON button(to turn on

the TV)

Press the DVD device button(to change to the

DVD mode)

Press the DEVICE POWER ON button(to turn on

the DVD)

Press the SAT device button(to change to the

SAT mode)

Press the DEVICE POWER ON button(to turn on

the SAT receiver)

10. Press the ACTIVITY button.

After following these steps, each time you press

the Activity Button

, followed by pressing

the "2" Button where the Activity is pro-

grammed,, the remote will send all Power On

commands.

The "2" Button only sends the programmed

Activity when the Activity Button

pressed first. Otherwise, Button "2" sends the

normal, numerical 2.

Erasing Activity Buttons

Press the Activity button

and the Activity

Button (0~9, or AVR POWER ON) that you wish

to program, simultaneously. The Device LED will

light up.

Press the Activity button

again. The Device

LED blinks three times.

Note: Any previously stored commands on an

Activity Button will be erased when new com-

mands are stored on the same Activity Button.

rogrammed Device Functions

Once the AVR’s remote has been programmed for

the codes of other devices, press the appropriate

Input Selector

to change the remote from

control over the AVR to the additional product.

When you press any of these buttons, it will briefly

flash in red to indicate that you have changed the

device being controlled.

When operating a device other than the AVR, the

controls may not correspond exactly to the func-

ion printed on the remote or button. Some com-

mands, such as the volume control, are the same

as they are with the AVR. Other buttons will

hange their function so that they correspond to

a secondary label on the remote. For example,

the Sleep and Surround mode selector buttons

also function as the Channel Up and Channel

Down buttons when operating most TV sets,

VCRs or Sat-Receivers.

For some products, however, the function of a

particular button does not follow the command

printed on the remote. In order to see which

function a button controls, consult the Function

List tables printed on page 46-50. To use those

tables, first check the type of device being

controlled (e.g., TV, VCR). Next, look at the

remote control illustration belonging to the

Function List. Note that each button has a num-

ber on it.

To find out what function a particular button has

for a specific device, find the button number on

the Function List and then look in the column for

the device you are controlling. Most of the but-

tons are fairly straightforward, as they perform

identical functions for all devices, but some have

other functions for some devices.

44 PROGRAMMING THE REMOTE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Harman Kardon AVR255 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Harman Kardon AVR255

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info